Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Dear all:
I have viewed that matter support below Operating Systems from this link:
project-chip.github.io/.../BUILDING.html
Tested Operating Systems #
The build...
Hi engineer I am using two nRF52832 boards to test the communication between ble_peripheral and ble_central. The project used is ble_app_uart and ble_app_uart_c in SDK15.0...
hello Nordic
i am using nrf52832 and nrf52840, working with ncs v2.3.0
currently i am using the SMP service for DFU but i also want to use the service's property to...
I b ought three ebyte E104-BT5040U USB dongle but it doesn't work.
I was program a ebyte E104-BT5040U USB dongle using openocd。I use daplink (2023-8-24) and openocd 0...
Mirroring the issue from Github here I'm working on an application with timers and PPI. Today I discovered that when using the function nrfx_timer_extended_compare with a...
Hi,
We have been trying to get the audio application to work using an external I2S microphone, but have recently run into the following problem when trying to send audio...
Hello Nordic,
I've been attempting to convert our system's TWIM implementation from the blocking to the non-blocking mode. I have been able to communicate fine with the...
Hi,
I have updated finally Segger Studio from version 7.22 to 8.14. Now I cannot compile the project. It ends with below error:
Build failed, exit status 0x1
Is something...
Hi, I have a problem where the mcuboot do not seem to include the 'jedec,spi-nor' driver. Looking at the build directory, /build/zephyr/zephyr.dts file has the device spi...
Hello everyone
our current project is to use dht22 to control an external fan
but we don't know how to add a new node to the device tree for the fan.
The picture below...
I got the license key for segger studio but the option to install the license is not popping up. https://drive.google.com/file/d/1qok8PcCYhHi_9nsknL2JW4_AtF6F5ZP5/view?usp...
Hello I have a few questions
In my project, the nPM1300 fuel gauge example via nrf5340dk works properly. I received information such as V - I - SOC via I2C. Currently I...
Hello, I'm currently looking for a comprehensive example of DFU-OTA (Device Firmware Update Over-the-Air) using the latest SDK version with the nRF5340 platform. If anyone...
Hello ! I'm trying to adapt the code from the master-slave SPI example ( https://github.com/too1/ncs-spi-master-slave-example ) for my nRF54L15 development kit.
The master...