I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hey,
in our project the nrf is acting as the central and connecting phones.
As part of the connection process:
1) We check if the phone is bonded in the nrf.
2) We...
Hi,
I'm on NCS 1.8.0 and I've successfully built and run the peripheral_nfc_example sample. Printed logs when reading NDEF message using a smartphone
When I came to...
I have a nRF52840-DK that stopped programing.
As a starting point to get it back to work, I reflashed the Interface MCU Firmware.
It is correctly detected by J-Link Configurator...
Hey Nordic,
My project is based on "ble_app_uart" and "ble_app_uart_c" examples. I modified them to some extent. You can download them from here .
Normally, I can write...
Hello!
On 3 and 7 of August my employee directed to you several questions regarding NRF. Case ID: 293339
Can I at least urgently receive the answer for the question in...
Hi,
We need to test our product for reliability when it comes to BLE connection in the vicinity of other BLE and WiFi devices. Do you have any suggestions on how to perform...
Hi all,
I am trying to use the bt_disable functionality on Adafruit Feather sense which has nrf52840 to restart a connectable BLE Service. The first call to bt_le_adv_start...
I'm developing an application using the NRF52840. I'm using the ADC, and there may be times where the signal to be measured is up to 1.8V, but the NRF52840 is not yet powered...
I am using the NRF52840-DK REV2 to program my custom board. I am using the debug out port and connecting it to my custom board, I tried both powering the custom board through...
Dear Nordic Engineers
I have a problem and would like to ask you about the I2C work state.
I read this link: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
Hi All,
I am working with NRF beacon project currently, and I explored many other NRF connect SDK sample projects like, Ble peripheral, ibeacon etc. But I am unable to...
Hi,
I'm trying to implement FreeRTOS on nRF52832 using the S132 SoftDevice and SDK version 17.1.0.
This is meant to read multiple sensors at a configured frequency ...
Hello all,
I have managed to connect the BLE module, based on the nrf52820 via the SW (4 pins) to the nrf52dk and surprisingly programming works via the Segger EM !
Indeed...
Hi,
I would like to carry the full modem update. Based on nordic website I need at least 4MBytes of flash for doing a full modem update on the nRF9160:
https://developer...
I have two Windows PC’s with an installation of SEGGER Embedded Studio on each and a nrf52832 project.
With the project and the library on a USB memory key running the debugger...
