Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I have
nRf52840 DK - 1 - Mesh Serail example nRF52840 Dongle - 2 - Mesh Light Switch Server example.
I used the steps given in the infocenter to provision and configure...
Hi,
Is it possible to be in connected mode (exchanging data) and also advertise data packet (on primary channels) between two BLE devices (so, in both the modes) ? Is there...
When using nrfjprog over an IP connection, `--ids` never returns a value. This is frustrating as the Zephyr nrfjprog runner uses this command to determine if there is a board...
Hello !
In latest errata, https://infocenter.nordicsemi.com/pdf/nRF52840_Rev_3_Errata_v1.1.pdf is not so clear all details of this anomaly
[254] RADIO: External PAs, FEMs...
I am trying to port a timer over to the nrfx_rtc driver and I can't seem to get it to start counting. I'm sure I'm missing something small, but I'm not seeing it. SDK 17,...
Hi,
I have a medical device where my mother board has a NRF52840 chip which communicates with a Android Tablet through blue-tooth. We find it gets connected with few tablets...
Hi, I am working the Zigbee in nrf connect SDK 1.9.1 I am running light_bulb, switch and coordinator examples
I want to change the panid , Short id, via proj.conf
how...
Hi,
Greetings!
I am using below setup
nRF52832
Mesh SDK 4.0.0
SDK 16.0.0
Application Example: light_switch_client_nrf52832_xxAA_s132_7.0.1
Issue:
Using above...
I am using SDK 17.1.0 with an nRF52832 design similar to the P10040.
I was previously using the original timer application and things were looking good. I decided to upgrade...
SDK: NCS 2.0.0
Based on: Peripheral LBS example
Central: Mobile (iPhone)
Peripheral: nRF5340
IDE: VS Code
Hi Everyone,
I am porting an existing project based...
Hello All,
We are intending to start a new project using nRF52840 SOC, for the same i decided to work with nRF connect SDK as it is recommended by nordic,
I am new to...
Hi everyone
We have developed a smartwatch with a nrf9160 chip. We have used nrf Connect SDK 1.2 for the development process.
Now we want to migrate our project to nrf...
Hello there,
I am using the peripheral/radio/transmitter and receiver example in SDK17
But I am only able to transmit 2 bytes. I want to transmit like 8 or 9 bytes...
Hi,
I am testing FOTA function using sample "http_update/application_update" on NRF9160DK.
But found that the system boot stuck at
I had tested this sample with...
HI
I am using this sequence functions in my main loop for low current consumption
__SEV(); __WFE(); __WFE();
normally I have 13mA in my application when I am using...
