I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi, I have external PCB, looks like this:
Need help with flashing the nRF52832 chip via nRF52 DK, please. External PCB have identical pin assignments as QFN48 pin assignments...
So, i just got some modules from minew, those are MS50SFB2 ( https://www.minew.com/product/nrf52810-ms50sfb2/ ) based on nRF52810. I uploaded the blinky example on one of...
Hi,
I am using nRF SDK 1.9.1. Want to add a few ASSERT to check corner cases.
When I add the following code in main.c
__ASSERT(buf == NULL,"Test ","Test");
The module...
Hello,
I was trying to store some information in flash using littlefs. when I build and run the littlefs example alone it works fine as accepted. However, when I configure...
I have nRF52840 Dongle and I want to sniff packets between two BLE devices. When I search in the Nordic DevZone forum, there are inconsistent answer about BLE sniffing support...
Hello community!
I know this sounds almost impossible... but it's happening
I'm debugging an application based on peripheral_uart. When I call
bt_nus_send(NULL...
hello. I want to use the button as a pull-down. I am using nrf52832, and the button and circuit part are composed of pull-down and the code is written as follows.
However...
Hello,
I can't find anywhere the height dimension for the nRF52832 WLCSP. There is width, length but no height, what is the height of this product ? Thank you
I am trying to use puncover to estimate the maximum stack size for the created thread.
We also tried the thread analyzer, but gave up on it because it did not seem to be...
I am using S112 softdevice along with SDK 15.1.1. The chip that I am using is nRF52832 and ble uart example
I want to make advertisement non connectable and non scannable...
hello Nordic
i am working with nrf52832, ncs 1.7.1
i am trying to work with external flash driver (25lp128)
so my dts looks like this:
my configs are this:
myboard...
Hi,
For some time I'm developing application for both central and peripheral devices. The Idea is that both devices have a special mode in which they pair & bond and add...
Hi,
I am developing a project that includes transmission and reception in particular timeslots. I checked the radio example in nrf5 sdk and copied the trasmission part to...
The direction-finding white paper shows an example for the NRF52811.
I have tried the example to get some NON-softdevice based code and several variations thereof and...
