hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1
Hello. We are preparing production. So I have to provide flash tool as well as binary only to factory without develop...
Hi there,
We are trying to enable the interrupts on one of the UARTE peripherals, and are having trouble finding the interrupt number within nrf5340_application.h? It is...
Hi Everyone,
The custom device I am working on is a BLE peripheral device and uses softdevice S132,
therefore to get accurate triggering of ADC sampling and to avoid periodic...
Dears,
We are MCU Programmer Supplier, now we are developing the off-Line Programmer for NRF5340, and encounter some problem as below:
1. Does the Nrf5340 Flash Memory...
I have a custom model server that sends 8 bytes of data
I set up 2 nodes - one to publish to an address 0xC002, one to subscribe to publication
Provisioning and publish...
Is there any documentation/tutorials for using NRFX drivers directly in Zephyr without trying to create conforming device drivers? I have a lot of code written for the NRF52840...
We have a board based on the nrf9160dk.
The project is essentially based off the "LTE sensor gateway" project with hcl_lpuart to utilize the nrf52840 for BLE. Chip shortages...
Hello,
I am performing garbage collection. During the garbage collection an event could be fired (from the softdevice) that causes updating of records.
My question is...
Hi
I would like to know, if Zephyr-s ssd16xx driver supports display driver board power supply control? I see from Zephyr documentation ( solomon,ssd16xxfb (on spi bus)...
Hello,
I recently installed the nRF Connect extension for VS Code on my Mac M1. I am unable to see my connected board as part of the nRF Connect extension.
Setup
...
Hi,
I see that the latest Nordic SDK ( v17.1.0) supports mbed TLS version of 2.16.10 only. However, we have received a End of life notification for the same ( Mbed TLS...
Dear All
Could you point me a timer example, can be used to time the interval in ms between something? like read the system time when something happens and then read again...
Is there a way to find you the reason for RRC Connect?
I'm using a simple software developed based on NCS AWS IoT sample. I've implemented the SW to test power consumption...
Hi,
I need to configure an nRF52832 to wake up periodically from SYSTEM_ON and SYSTEM_OFF and, also, when a GPIO pin changes.
Where can I find sample code and docs for...
