Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi all,
I want to implement a calendar that can be used for many years with nRF52840.
Will leap years be corrected in the nrf5-calendar-example? I looked at the code...
Does anyone have an example of using pinctrl and pwm on a Nordic device using Zephyr for a motor driver or something like that?
All the examples appear to NOT use the pinctrl...
Hi.
Setup:
I use NRF5340. Open project from SES menu "Open nRF Connect SDK project".
nRF Connect SDK Release: 1.4.99-dev1. nRF Connect Toolchain Version: 1.4.0.
Project...
Hello! I tested the ST BLE Sensor sample on my nrf52840 DK. I have a few questions about the source code: 1. Looking at recv(), connected() and disconnected() functions, seems...
All nRF5340 reference designs use via-in-pad structure. Instead e.g. nRF52840 has reference designs which can be used with through hole PCB.
nRF5340 seem to have 19 IO's...
Hi,
I'm trying to do a very simple thing - setting those pins as high or low,
but I see that it simply does not work for those pins, I see no change in led state that...
I am using the SLM app from the 1.9.1 SDK.
I connect to my MQTT broker using TLS offloaded on the modem. I subscribe to a topic using QoS = 1 Then if a message is published...
I have been trying to get mqtt to stay connected without activity for more than 30 minutes. any keepalive value over 30 minutes just results in mqtt discoonection. tried with...
On a custom board, I've got 2 inputs connected to an external pullup and a pad. One in is P12, one on P21.
When I short the pad for P12 with GND, that input read low, that...
Hi,
I tried to access Nordic devzone, yesterday and today, but got an error message that "the page cannot be displayed because of an internal server error has occurred...
Hello everyone!
I am trying to figure out how SPI drivers for Bosch bme280 sensor work... I would like to somehow recycle them to write my own SPI drivers for another device...
Hi Nordic,
Using nrf-connect 1.9.99 and Zephyr 2.7.99 (*** Booting Zephyr OS build v2.7.99-ncs1-1 ***)
I am using then nRF9160-DK and everything is fine. Getting 40uA...
I'm running Manjaro Linux and have ran through the installation instructions for the nRF Connect Desktop. I have separately downloaded the Segger JLink software as instructed...
Hi Team, In my project i am using nrf52833 and i have established a network using Open Thread protocol to communicate . I am able to pair my device with the network. One scenario...
Hello, I am using 52832. There is an external interrupt count with a maximum frequency of 1kHz. I have two hardware. One I transmit to the mobile phone at an interval of 50ms...
