Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi,
I'm trying to create a custom board definition for our project. So far, I used the nRF5340DK's board definition, removing unwanted definitions and aliases from the DK...
I am receiving the error "qspi_nor JEDEC id [ff ff ff] expect [c2 28 17]" on device bootup. I am using the nRF52840. I have the qspi disabled in my device overlay.
This...
I just move code from main.c to other files for it is too chaos to lay them together in main.c.
I got this error forever after trying what I can image,except delete "static...
Prior to moving to sysbuild, we were dynamically settings a CONFIG_ variable in our `CMakeLists.txt` based on the board passed to west. And this was working fine.
if...
I've had trouble getting the MCUboot to compile for our application which runs on the nRF7002DK board, and I have similar trouble with the Lesson 8 examples on the nRF7002DK...
I have searched this website,there is only 1 post,but that is not my scenario.
I think this is a normal use case:
There is a struct:
I want to allocate a queue for...
Hi!
I have a bootloader using SPI 3 for a bootloader LCD animation. Unless I attach an RTT console, the animation causes my DFU to fail 100% of the time. It is making me...
Hi,
Since I want to flash the factory data later, I don't want to use the default certificate. I set CONFIG_CHIP_FACTORY_DATA_BUILD to n in prj_release.conf , but a compilation...
Hi Sir, We are planning for a Hardware deign by using nRF52833 and we are stuck on what should be suitable the supply voltage. In some case the data sheet showing that it...
Hi there,
I'm encountering an issue while trying to flash a PWM example built with NCS v2.9.0 on Windows 11 (using Python 3.10 ). The build completes successfully and generates...
I have a collection of nRF9151 devices using PSM mode.
Each time the application attempts to send UDP data while in sleep mode, they get a detach request (from the network...
Hi
I have two nRF52833 development boards: one is using BLE peripheral_uart, and the other is used as RX (BLE central_uart). My issue is that, with the TX setup being completely...
When a button is pressed during power off, the buttons module disables the wakeup interrupt but the button scan never happens, leaving the module in an invalid state and preventing...
Dear Nordic support,
I was reading the Technical Documentation in the GPIO section for the nRF9151 , and I came across this blurb:
"Note: When a pin is configured as digital...
