Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
Hello,
I'm working on a project involving both the nRF9160 and the nRF52833 on a single PCB. Since PCB space is at a premium for this project, I would like to know if it...
Regarding the new modem command AT%RAI, the documentation here says:
In addition to using the %RAI command, the application must tell when the data connection is not needed...
I have logged in, I am using the same email address and I have read and - I believe - qualify for the license agreement.
Can you please look at why my request is denied...
Hi,
I am trying to migrate my project from 52832 to 52810, somehow i found the services can't be discovered. And seems that on phone it's looks like it is connected, but...
Hello,
how to activate the Early Release Assistance Indication, to bypass the RRC_CONNECTED state.
This page from Telekom suggests that the user can do that to save much...
I saw in some post smart Bluetooth can have 7 active device. I would like to know what is the maximum number of Bluetooth devices i can pair up in sleep mode? i am doing a...
Hi,
I'm using SDK v17.0.2 on my nRF52840-based board. I have implemented buttonless secure OTA reflash and it generally works. When I get the NRF_PWR_MGMT_EVT_PREPARE_DFU...
We have some dev code where the workflow is as follows:
1. an engineering version of firmware is loadded to target. The target is erased then programmed in the normal way...
Hello,
I am using nRF9160 dk for prepare a program to I2C scanning for address. Can any one give a guide for start this task. Moreover, I am using Zephyr kernel on nRF9160dk...
Hello,
I want to read external accelerometer on nrf9160dk using I2C. But when I connect SDA and SCL pins of sensor to nrf91, there is no output.
The Code is:
When...
I am trying to set the UUID definitions for the Windows Application Bluetooth Low Energy 3.0.0. The only doc availible is for v2.3.1.
I tried to follow the following steps...
I'm using nRF SDK 12.2.0 and the corresponding soft device. I control a I2C slave for which I use the TWI peripheral through the driver implemented in nrf_drv_twi.c. It happens...
Hi,
I trying to enable Hardware Key for mcuboot.
I do the following at mcuboot.conf
CONFIG_BOOT_HW_KEY =y
But I got the following error:
Do I miss something...
Hello, I test SAADC on nRF52810, when I short gound to AIN0, the output is 0 normally, and when I add nothing to Pin I0(AIN0), the output is around 1056(Figure0), however...
