Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi there,
I am trying to obtain a .hex file for my project for Release Configuration. I don't see the .hex file get updated in the pca10040\s132\ses\Output\Release\Exe directory...
I am a electrical engineering student in my final year of study and am developing a product for my final year dissertation.
The project idea is to help identify sickness...
Hello,
I am using,
iPhone 7
iOS v14.8.1
nRF Connect for Mobile iOS v2.4.13
I have used nRF Connect for Mobile on android which shows this menu when peripheral...
I am using the NRF52840-DK and using the Zigbee light bulb example.
1. The DK board successfully connects to the zigbee network - Z2M in this case.
2. I have added an...
Hi everyone, my colleague developed a firmware using Arduino Nano 33 BLE and PlatformIO. Now I have to rewrite the code using Segger Embedded Studio. The problem is in the...
Hi there, I am developing a peripheral to central system with nrf52840 base on NUS service. Now I tried to increase the MTU of the peripheral to 247 to increase the transfer...
Hi,
I am using NCS for development and configuring GPIO pin as input, but I found the GPIO can't configuring as NO-PULL mode. There are only two options: Pull up and Pull...
Hi,
I am working on ble_bms_app template. While the nrf52840dk is connected to laptop, I don't get JLINK connected notification on the desktop. Sometimes i get the connected...
Hello.
I'm using nrf52832 (S132 v7.0.1, SDK v17.0.0) to develop peripheral roles.
Setting UUIDs for advertisements, services, and characteristics. At that time, sd_ble_uuid_vs_add...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0) as central and Android device (Bluetooth 4.2) as advertise. Android devices use nRF Connect.
I can set...
We are aiming at a low pin count interface between modules. Ideally we would like to use the programming pins for both programming and as an I2C interface. Is this possible...
Hello,
I am new to Nordic, Zephyr and Linux. I have been going through the "getting started guide" on the zephyr docs website and ran into this problem not being able to...
I heard that nrf52832 rev3 has been released. Our product is using nrf52832 rev2, nrf SDK 15.3. If we change the chip to rev3, can we use the firmware without modification...
