hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
hi,
we use the NFC Tag Type 4 of nRF52833, it can be listened to by mobile apps and read or writed by apps. But when we use NFC reader to listen this tag, the card reader...
Hello!
I'm in the process of prototyping a PCBA that is Battery Powered with VDDH (Tied to VDD for now), but also has the option of USB Power.
When USB Power is active...
Hi,
I understand 'nRF Sniffer for 802.15.4' is typically used with nRF52840 DK or nRF52840 Dongle.
Would it be possible to use it with nRF52833-DK instead? If so, any...
SD: s132_nrf52_7.2.0_softdevice
SDK:nRF5_SDK_17.0.2_d674dde
I was running the firmware with debug mode. It only has an application timer and Bluetooth. I feel it might...
Dear Sir/Madam,
While I did take a course in Bluetooth I am still a beginner.
I know some boards have HID "support" (RN42 for example) I find it hard to believe that it...
Hi, Recently I bought the nRF9160DK for development and during get start i am facing some issues
for get starting i am use this video as reference https://www.youtube.com...
Hi all, I am using Arduino nano 3.3 BLE in my project. I am using light_lightness server as the program for the nano boards.
However, I found a difference in the transmission...
Hi everyone,
I want to sample eight analog sensors connected on P0.30 through a multiplexer. I created an app_timer that expires every 10ms. When the timer expires I start...
https://devzone.nordicsemi.com/f/nordic-q-a/82644/nrf52832-freertos-ble_app_hrs_freertos-lowpower
I mentioned the above problem before. After your support, I found that...
Hello everyone,
my application is build based on the mulitrole example. The device name is somehow limited to 4 letters.
I checked:
init.advdata.name_type = BLE_ADVDATA_FULL_NAME...
Hello, I attempted to enable the zephyr task watchdog model but whenever I configure it to enable the hardware watchdog module I get the error above. Any idea why I am getting...
Board: NRF52840
SDK: 16
Soft Device: s113
So our board is custom and does not contain a crystal. We are treating P0.00 and P0.01 as GPIOs for button inputs. P0.01 works...
Hi all,
I was able to create a mesh network with two nrf5340 boards configured with the mesh light sample and the mesh light switch sample.
I am trying to substitute...
Using SDK15.3 on 52840. I've got a UART set up talking to something at 9600 baud..
The short course here is that imediately after init, I get an IRQ with a NRF_SERIAL_EVENT_DRV_ERR...
Hello, I´m working on my audio project and I try to stream some audio data (currently a 1 kHz square wave signal with 3.3 V peak) over I2S. The audio signal is sampled by...
