I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi
I configure two IO output PWM, one of which outputs PWM all the time, and the other turns on PWM by timer intermittently ，The period of the former becomes wider，As shown...
I’m not able to connect my Thingy91 to the network. I have successfully registered my Ibasis SIM card in the nRF Cloud (or at least that is what I think I have done):
...
Hi,
I am trying to configure a basic output pin in the device tree configuration. I read somewhere a 'compatible' parameter is requires because it describes what will be...
hi team,
Intial we followed this link for system on --> https://embeddedcentric.com/lesson-14-nrf5x-power-management-tutorial/
Now we are trying to enable the constant...
Hai
I have an NRF52840 Development board with 1MB of flash. I have an requirement to store a large amount of data in a flash around 6k samples in one record.
For this...
Hello,
Im using E73-2G4M08S1C module based on nrf52840. Somehow even when in erased state its consuming a lot of energy and starts heating very fast.
Im trying to figure...
Hi Nordic team
I failed to demostarte multicell location sample.
Hardware: Thingy91
SDK: v1.6.0/multicell location
Modem: v1.3.0
Q1. At prj.conf, nrf cloud location...
Hi Nordic
We are developing our IOT product and we are starting our development of firmware on nRF9160 DK so that we can port that code to our custom PCB that will contain...
Hi,
My application is currently using s132 v5.1.0. The Release notes for s132 v6.0.0 say:
"Fixed an issue where incorrect timing calculations during the LE Data Length...
Hello
I am running this version of SES
SEGGER Embedded Studio for ARM
Release 5.34a Build 2021011401.44914
Nordic Edition
Windows x64
When I run my program in...
Hello,
I am using the pine watch hardware, to do some tests,
I configured through the overlay file, the I2C_1 to use pins 0.6, 0.7 as shown below,
&i2c1 { compatible...
Hello,
I'm playing with the timing subsystem in order to measure some execution time with higher granularity than the RTC tick on nRF52840 (using PCA10056 DK).
I'm specifically...
Hello sir,
I am using nrf58232 Dev kit board in which when my BLE goes is in advertisement board and after couple of seconds advertise APP_ADV_DURATION is expired then it...
Similar, unresolved issue can be seen here .
I just got my official nRF52840DK and setup nRF Connect on my MacBook. I'm able to build the Blinky example and flash it...
Hi,
I have the following in my code to measure throughput over the Nordic Uart Service.
It works, but I was wondering if I am measuring correctly. I took this measurement...
