Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hey all,
Custom service, but my first where I am looking for more than one byte of data written to a characteristic at a time - in this case 8 bytes. So everything looks...
Hi,
My project involves an nRF52840 DK connected to an accelerometer on a breadboard, connecting to my Mac via USB-micro.
I'm editing the twi_scanner SES project so that...
Recently I received the nRF5340-DK. I tested and it was working correctly and as a test, I compile one of the ready solutions of NRF5340 of SEGGER Embedded Studio. Everything...
Hi, I am getting an error 19 which causes a reset after some time running a modified version of the ble_nus peripheral example may someone guide me on how to sort the issue...
Hi, what is the nRF52DK UART, for the nRF52832, flow control when using the ble_app_uart_pca10040_s132 example? It appears to be possible interrupt driven based on data received...
So ...
I'm still trying to get peripheral_uart running.
I'm using a nRF53 PDK (PCA 10095 - rev 0.8.0) (I've received two 0.11.0 boards, both of which died).
I'm using...
I'm using the nrfx twim driver along with Zephyr. I'm using the NRFX_TWIM_EVT_DONE to initiate a subsequent TWIM command and finding that the second command fails due to the...
Dear community,
I was working with a modified code based on an example for switching the leds on/off in a Mesh BLE network. Everything was working well until I tried to...
hello Nordic
i am using nrf52840, SDK16.0, a project build on the peripheral app_ble_blinky example
i am trying to use QSPI but the write function falls on error no...
Hello together,
I try to get the asset_tracker_v2 up and running on the thingy:91.
At the moment I get an Error from AWS_iot aws_iot: mqtt_connect, error: -116
My problem...
Hi Nordic,
I am trying to use the nrf52840 to talk with my 4G module on baud rate of 115200 , but I find it always come into error for the recving the uart data. Also it...
Hello,
I have an nRF9160 development kit and was measuring the time it takes for switching off the modem
when it has an open data connection.
I did it by sending an...
Hi,
I'm currently working on NRF52832 (Softdevice s132 6.1.0) controller and developed a firmware from light switch client to develop a mesh network and its working fine...
Hi sir,
I have downloaded the NORDIC THINGY52 SDK from the given link https://devzone.nordicsemi.com/f/nordic-q-a/51236/unable-to-compile-ses-project-in-thingy-52-sdk (As...
Hi,
What do I need to be able to FOTA when nRF Connect SDK is updated?
For example, when the SDK version is 1.6.0, can I use the changes I made to the new SDK version...
