I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Background : We developing lighting product and planning to use nRF52833 module and we planning to use the latest SDK version that is nRF5 SDK for Mesh v5.0.0. First step...
Hi,
We're doing some testing of mesh protocols and their latencies using the nRF5340 DK. We want to isolate the wireless communication from interference as much as possible...
Our project uses nRF Connect SDK v1.5.0. Two main developers work with the files in very different environments.
I am not sure if this was an accident of initial development...
Hi,
I am currently running a custom bootloader I found that updates via SPI. I have 2 nrf52840 DKs that are programmed as an SPI master and a SPI bootloader. I have been...
After developing with an nRF52 832 DK (pca10040), our code builds and runs fine. But when we try to use the same code on the nRF52840 dongle it does'nt work. We added flashing...
periodic_adv sample is not working with nrf5340dk_nrf5340_cpuapp
it is working for nrf52840dk_nrf52840 after adding CONFIG_BT_LL_SW_SPLIT=y to proj.conf
Here is the log...
My problem is the that on some devices the ScanResult.getDevice() or ScanResult.getScanResult() both return null on some devices but works fine on most.
This is probably...
Hi folks,
I want to calculate the timestamp for which my thingy 52 board was scanning from another thingy 52(may be more than one board). Is there any technique to get the...
I am confirming ADC sampling 420Hz operation by following question.
https://devzone.nordicsemi.com/f/nordic-q-a/69096/1khz-or-more-adc-sampling-rate-over-ble
The source...
Hello,
I am using the nrf9160DK and I am implementing on zephyr.
For my application I need to write to an external flash memory through I2C. I need to write one page at...
Hello
We are using the NINA-B1 on one of our products.
The phone application is working 100% and was very easy to setup.
Till we came to connect our frontend to...
Hi:
we set p21 as Hardware Reset Pin by config UICR.PSELRESET[0] = UICR. PSELRESET[0] = 21
when we use these code to check halt state, but always get DBG_HCSR zero value...
Hello,
I am attempting to install the nRF Connect SDK v1.5 on a Mac Mini with Mac OS 11 with Apple M1 Silicon per the instructions:
https://developer.nordicsemi.com/nRF_Connect_SDK...
We are using the Nordic fork of Zephyr on nRF5340.
Looking at the serial interface peripherals (SPI/I2C/UART), we understand that these have shared resources and only one...
