Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Can you please provide security manager keypress notification sample program for bot peripheral and central program. I want to know why it is used and what is the main purpose...
Hello Nordic team
I am developing a BT mesh network project, which be implemented by nrf52840. Right now I am designing the node PCB. I want use the No.4 reference circuit...
Hi,
I tried to implement my custom service.
I followed the tutorial from this site: https://github.com/bjornspockeli/custom_ble_service_example
For SDK 15.0 it works...
I'm attempting to connect an SDcard (micro SD) to an nRF52840-DK via a breadboard setup. I'm running Zephyr and it appears that configuration is to be performed via device...
I'm trying to investigate whether I should ditch BLE in favour of Gazell and ShockBurst (to avoid the $8000 Bluetooth.com fee)
I've noticed that Gazell has no entry in the...
Hello,
I've got this Thiny:91 demo working nicely, but what I'd like to do now is only measure RSSI.
Is there firmware to only do this?
Like send AT commands only to...
Hello,
I've been trying to perform a dfu to a target Nordic device over Bluetooth using an nrf52840 dongle distributed by Laird, however whenever I attempt to run the command...
Hi guys,
I am trying to create a zigbee mesh with 10 devices with 1 coordinator and 9 routers (all are nrf52833 based custom board). I can create a mesh network easily with...
Hi,
I understand that white list can be enabled at the peripheral side. I also know that if white listing is enable on the peripheral side then it wont respond to centrals...
Hi All !
Hope you are doing well !
I have tested some examples using SDK 17.2.0 and it worked fine ! .IDE i used is SEGGER IDE . Now i have a question that my next HW...
Hi,
I'm testing the USBD BLE UART Example with nRF52833 DK, after programming the app, the LED3 keep it off all the time as followed.
In the device manager, I can see...
I'm porting from 1.2.0 to 1.4.2. I'm using mqtt_simple as a baseline but I'm connected to Google Cloud. I successfully create a socket;
net_mqtt_sock_tls.mqtt_client_tls_connect...
Hi:
Now i am development the OTS, the default connect parameter is:
interval_min = 24 （30ms） interval_max = 40 (50ms) latency = 0 timeout = 400 (4000ms)
But i got the...
Hi,
I want to receive UPD message on my nRF9160-DK. I can send UDP messages from my Nordic device to a server and from that messages I get the public IP address of my module...
I want to use I2S on nrf9160. I found some code on the its user manual and try to run in my project. But when the device is running, it always reboots. What other configuration...
