Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi,
I would like to know if the LFCLK is enabled after zboss_start(); and after zboss_start_no_autostart().
I would like to use an rtc event to trigger a PPI routine and...
Question: for the nRF52840, if I configure a GPIO pin as an open-drain output (DRIVE setting of S0D1) and then select this pin as a UART transmit pin, does the open drain...
1 .after the flashing the board i get a Zigbee Connection and Bluetooth connection but i can't able to control the bulb by using both board and bluettoth
2. Sir i am using...
Dear all.
I know the nRF52840 has 2 uart module.
I've been used only 1 uart setting like below pin connecting in 52840 DK reference doc.
But now i have to use 2...
*** Disclaimer *** I am a total rookie on this technology *** Disclaimer***
I'm working on a small BLE proof of concept and I have an nRF52840DK board. I've got Wireshark...
Hi, guys! I'm using the nRF52 SDK 15.3 BLE_APP_UART peripheral example.
I wish to add 3 ADC channels (12-bit) to read 3 potentiometers at a sampling frequency of 6kHz. ...
Hi,
I've BLE custom data sent to nrfcloud and looking for ways to plot data. I've used "add custom card" from configuration to extract data but was not able to plot/view...
hi, I am working on nrf52832 platform and tested some Bluetooth examples of SDK_15.3.0, I want to test some Bluetooth examples like audio, media and etc, is there any project...
Hi,
I am using a BLE master to bond with nRF52832. SDK is 15.3.0. Both side support secure connection.
I have tried to set the address type of master to public or random...
Hi, I'm starting to use the nRF52840 DK, I have downloaded the segger embedded studio but I don't have idea how to start, I need a sample example to use the pins to control...
I am new to Nordic products. I have a custom nRF51822 board and I want to flash it with Keil uVision and ST-Link V/2.
As I understood, I have to program the SoftDevice firmware...
I'm implemented DFU (with custom transport, but the problem is not there). Even when flashing SD+bootloader+app+settings I can see an error in the logs:
```
14:23:48.096384...
NRF Connect sees the devices no issues and connect. When it comes to running any of the examples in the toolbox, the devices are never seen. Location services are allowed...
Hello,
one small question: If we switch from Softdevice S132 6.1.1 to 7.0.1 without recompiling the application or using a higher SDK, does it mean, that we will automatically...
