When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi
I am trying to connect and bond a nrf52832 to Galaxy S6, Android 7.0 by OOB / NFC with the ble_nfc_pairing_reference_pca10040_s132 example.
I selected LE Secure Connections...
Hi nordic,we want to config nrf52832 as a wireless full-duplex serial port transmission module through nordic proprietary protocol，so the module can send and receive data...
I have my IMEI but my pin number has 4 digits: 0000, instead of 6 digits(which is required to add the LTE device)? Please Nordic, what should I do? I have this problem for...
Hello,
I have problems setting the output RF power to +8 dBm during DTM test using the example dtm application. The example dtm application is used as it is provided with...
Hello,
i've been searching the forum for answers about Bluetooth certification but i'm very confused.
I want to use nRF52832 in my project, and i would like to make make...
I am trying to transferAdvertisement data from NRF52832 to Raspberry PI using BLE_app_UART example. I have updated the config as below,
app_uart_comm_params_t const comm_params...
Hi,
So this may seem like a stupid question but here goes. I've been trying to learn how to implement an IoT solution.
While trying to learn more about MQTT protocol...
Hi,
I'm trying to build the example found here: https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/uart
and the build is failing with this...
Hi!
I've been trying to connect the nRf9160 to an AWS IoT account following the directions here https://github.com/NordicPlayground/fw-nrfconnect-nrf/tree/master/samples...
Hey guys I am using nrf52840 dongle for scanning ble beacons. I want my dongle to be power optimized in a way that it starts scanning for 10 sec and then go to sleep for one...
Hi,
I am working on nRF52DK. The Bluetooth MAC address is stored into the Flash during the pairing sequence. Can some one provide me the links to understand the storing...
hello
hi
I connect AT24C02 EEPROM with nrf52dk.
I connect SCL to 27 pin ,and SDA to 26 pin.
I open twi_master_with_twis_slave sample code and make some changes(i2c...
Hello there;
We want to develop a project using the nrf52 series. We have two nrf52s. The first one is in the center and connected to the mains and there is no battery problem...
Hi there i have serius problem in gettimng my nrf52840-dk to work, i am set up in Visualstudio code on a mac, avery thing compiles and seem to upload but nothing happens afterward...
