Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi,
I currently have a project which triggers a series of SAADC readings from the Timer0 interrupt handler. This part of my program works as expected, however, to add more...
Hi,
From this link https://devzone.nordicsemi.com/f/nordic-q-a/34224/device-does-not-reset-after-dfu I understand that the compiler option flto caused reset issues. Is...
Hi everyone,
I am trying to use Buttonless DFU to reprogram the NRF 52 dev kit OTA. I had posted a question on the forum and had solved that problem: devzone.nordicsemi...
Hello,
We have implemented DFU services in application but getting lots of difficulties for writing own transport layer for Wi-Fi to upgrade firmware from server. We are...
Hi...
i have done the program to read the temperature sensor, i want to get the temperature in float value . i can able to read the temperature in float but i can't able...
Hello Nordic Pro's,
We are developing a product based on the BLE UART peripheral. We communicate heavily via NUS. There are extended processes that continually send status...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) As per below link, do I need to skip GPIO...
I would simply like to see the debug outputs (NRFX_LOG_DEBUG) the NRFX_TWIM.C module using RTT debugger through Segger J-LINK.
I cannot find any documentation on how to...
Hi,
I am working in nRF52832 SDK15.3 in SES
I need to work on reading multiple Analog inputs. in a different timings.
i have seen SAADC example.
is there any multiple...
Hello,
I am working with nRF52832 , a soft based on the NUS service and SDK 15.2 ( S132) .
In the aim of reducing the current comsumption , I want to modify the throughput...
Hi Martin, I follow all the steps in your tutorial(Bluetooth low energy Characteristics, a beginner's tutorial) and I am able to create the characteristics and the notification...
How do I share variable data from my nRF52 application to the bootloader code?
Check the update to this question after first comment by @HungBui
There is some short...
Hi,
I am using three nRF DK (nRF52832 - PCA10040) to test and analyse the mesh network (nRF5 SDK for Mesh v3.1.0).
I worked on light_switch_example with 2 clients and...
Hi.
I'm using the nRF52810-QCAA (DCDC) Reference Design, but I've noticed that C6 and C13 are labeled as No Connected in both the schematic and BOM, but in the PCB model...
Hi,
I am trying to write data to the nRF52 module from my custom application. I am sending few parameters bundled into a packet to the module. One of the parameters is the...
