Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi...
i have done the program to read the temperature sensor, i want to get the temperature in float value . i can able to read the temperature in float but i can't able...
Hello Nordic Pro's,
We are developing a product based on the BLE UART peripheral. We communicate heavily via NUS. There are extended processes that continually send status...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) As per below link, do I need to skip GPIO...
I would simply like to see the debug outputs (NRFX_LOG_DEBUG) the NRFX_TWIM.C module using RTT debugger through Segger J-LINK.
I cannot find any documentation on how to...
Hi,
I am working in nRF52832 SDK15.3 in SES
I need to work on reading multiple Analog inputs. in a different timings.
i have seen SAADC example.
is there any multiple...
Hello,
I am working with nRF52832 , a soft based on the NUS service and SDK 15.2 ( S132) .
In the aim of reducing the current comsumption , I want to modify the throughput...
Hi Martin, I follow all the steps in your tutorial(Bluetooth low energy Characteristics, a beginner's tutorial) and I am able to create the characteristics and the notification...
How do I share variable data from my nRF52 application to the bootloader code?
Check the update to this question after first comment by @HungBui
There is some short...
Hi,
I am using three nRF DK (nRF52832 - PCA10040) to test and analyse the mesh network (nRF5 SDK for Mesh v3.1.0).
I worked on light_switch_example with 2 clients and...
Hi.
I'm using the nRF52810-QCAA (DCDC) Reference Design, but I've noticed that C6 and C13 are labeled as No Connected in both the schematic and BOM, but in the PCB model...
Hi,
I am trying to write data to the nRF52 module from my custom application. I am sending few parameters bundled into a packet to the module. One of the parameters is the...
Hi
Im currently having some problems with programming a solution for a small system that im making.
The idea is a mailbox with a dongle and accelerometer that senses movement...
Note that for SDK v12.3 : if application size * 2 > available space a single bank update is performed.
While I am using v15.3 and there seems no more infor about the single...
I installed espruino_1v99_thingy52_app and espruino_1v99_thingy52_softdevice , but i want to restore the thingy to the default firmware. Have a way to reverse to the default...
Is there some instructions to debug the nRF91 sample applications with segger with thread awareness? I've seen mention of freertos thread awareness and have requested access...