Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi all, I have some question.
When I using mobile to bond with my DK nrf52832. Infomation will save to flash via FDS library.
So, when I delete bond from mobile and rebond...
Hello
I am using ble_app_multilink_central on nRF52832 DK.
I want to collect advertising data from all peripherals and not connect to them. Problem is that I dont know...
Hi guys! I have had an issue with Image Transfer Demo project. I use nRF52832 with OV2640 camera. I used installation project process described on the page https://github...
Imagine i have a client which sends message to a gateway and i set a TTL for the shortest path . If one of the node is not functioning how will the mesh reroute the message...
nrf52840
sdk for thread and zigbee 2.0
windows
segger studio
in example simple coap cilent and simple coap server
I create my own packet error test through coap...
Hi All,
Currently in my project i'm using hard core delay and delay is custom i.e some places i have used millisecond and in some places used microsecond and in sec.But...
Hi all,
I may need some guidance on the finite state machine method which found an example in app_level.c (from nRF5 SDK for Mesh v3.1), please see my question on below...
What is the minimum specified voltage required on ENABLE (Pin 101) for proper operation of the nRF9160 SIP? Is it the traditional 0.7 VDD, or is it permissible to use a lower...
Hello, I work with an nRF52832 DK and I want to test the example code "ble_app_uart_coexist" . I use the S132 softdevice, SDK 15.3.0 and version 3.1.0 of the mesh for this...
Hi
I used the SDK14 with nRF52832, and carry out the blinky example. When using the Android, the BLE device could be found, but the IOS cannot scan the device. So could...
Hi,
So I am working on NRF52832 with S132 6.1.0 and SDK 15.2.0 mtu and data lenght testings. During that time I was unable to change mtu multiple times while connected ...
I have a ble device and want to write a byte array in nRF Master Control Panel. Firstly, it can be written. But i don't know ho w to input it. My byte array is [-128, -64...
Hi,
I looked at this comment.
If this function (sd_power_system_off) is executed, can I wake up the device again with a soft reset?
If not,
What is a function that...
Hi,
In the documentation nFR523832_PS_v1.4, on page 107, the registers HFCLKSTAT and LFCLKSTAT when in reset mode, indicates that the LFCLK is not runing, and neither the...
