I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
We are using an NRF52840. After initializing a UART that uses P0.06-TX and P0.07-RX the following function calls fail: sd_ble_gap_device_name_set() and nrf_sdh_enable_rquest...
I am playing with the TIMER peripheral and I am seeing that I must call the function "nrf_timer_event_clear" in order to get the TIMER interrupt to stop firing once a COMPARE_EVENT...
As shown in subject, I tried to register many BLE services, DIS, BAS, HTS, and Custom Service. Then nRF52832(and nrf52840 preview) has stopped by an error of NRF_ERROR_NO_MEM...
I am working in nrf52840 sleep mode and it is working perfectly in system_off() mode, but while trying to wakeup from sleep using timer the device is not waking up because...
I am configuring the SAADC for Single-ended mode which I would think is a simple/common task, but my output from the ADC is very jittery. It seems to jump between a good reading...
Hi!
SDK15, s132, SD6.0.0, nRF52832
I have nRF52832 in central mode and some bonded HID devices and another nRF52832 peripherial devices.
Now in the my central nRF52832...
I simulated the balun of nrf51822 accroding to the referenced design of nrf51822 on the official website. However,it showed the differential phase of the balun was not 180...
Hello team,
We are using CPU NRF52832/810. We have followed the THINGY hardware for BLE Antenna with Ceramic Chip. Due to our range requirement more than 100 meter, we wanted...
DK : nRF52840
SDK :15.3.0
example code : nRF5_SDK_15.3.0\examples\peripheral\flash_fstorage
I watched that using nRF52840 DK is best way for develop nRF52811. So I...
Hi,
We have a product that uses nRF52832, we are trying to get the FCC Certification. We are using the RF test example to setup the DUT.
We are able to get the signals...
Hi,
I wanted to use Nordi UART service, the problem is that if I have no contraction with the device, it would not advertise after a definite time, say 180 Seconds, my devices...
I'm trying to connect nRF916 FP1 Preview DK to LTE-M network using LTE Link Monitor but it fails. Below is details about my firmware/software:
Zephyr OS v1.13.99-ncs2
...
