I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
Hello,
I'm using the nRF9160DK (PCA10090 0.8.2). I was able to see the data coming from the nRF9160DK in the nrfcloud, but now I want to be able to see the data published...
Hi,
I'm working on nrf52832 NUS. When i connect to device with "nrf connect app" i can see the data coming from sensor. But few seconds later device disconnect.
When...
Hi,
To build the context: I have two peripherals, Sensor 1 and Sensor 2. Sensor 1 has been running off of a NUS service to transmit data. Sensor 2 has been running off of...
Hi all,
I make a key using nrf52832. It tranfer data to other device. I have 2 option for this. Using beacon (BLE) or Enhanced ShockBurst (ESB) . I want to optimize energy...
Hi all.
In our project we are using BLE, but at some point switch to ESB. The code below disables the SD, and sets up ESB which is then used from then on.
This all...
Hi,
I am using nRF52 DK PCA10040 to develop an application starting from the ble_app_uart example, Then I introduced PWM and SAADC from other examples, and after I verified...
I have an nRF91 DK v0.7.0 which I'm using for the first time with a Hologram.io SIM card and nothing seems to be working. Nordic sales and an FAE were here in late February...
Hello,
I need to get nrf9160 to connect to a LTE-M network. We are using a custom pcb module with nrf91 on it. I've managed to get a simple hello world, blinky and gps simulator...
Hi,
I am currently working on a project in Mesh on nRF52840 DK.
I am using the mesh v3.1.0.
I wanted to send command from mobile app to particular node in the mesh and...
Hi, i use the saadc example(triggered by ppi+timer) with uart to get voltage signal and transmit to central device( another custom nrf52832 board), and the central prints...
I am using SPI communication to transfer data from an ADC (ADS1220) to my nrf52382, then to the mobile app via bluetooth. The ADC is the slave. The NRF is the master. So MISO...
Hi,
I am trying to read data via an ADC through SPI and send it via Bluetooth to the NRF mobile app. I checked that both the original BLE_UART example and the SPI master...
My SPI data transfer from a peripheral ADC works fine in the SPI example project. The same code doesn't transfer data properly when it is added in either a ble_template or...
Does the BLE NUS service use pins on the NRF? I'm using a custom made nrf52382 pcb where I transfer data from an ADC (ADS1220) via bluetooth to the nrf Toolbox app. But using...
