I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Dear Sir,
I am working on SDK15,nrf52832 and soft device S132.
I was working on the following scenario.
A peripheral device advertise as soon as it is switched ON. ...
Hi, nordic
I get some problem when developing the ancs with SDK15.0.
I run the demo with ble_app_ancs_c on the board of PCA10040.
First of all, after my iphoneX (system...
Hi all, development software: nrf5_SDK_for_Mesh_v2.1.1_src\examples\light_switch\proxy_server Board 1 nrf5_SDK_for_Mesh_v2.1.1_src\examples\serial Board 2
IDEs: SEGGER...
Hello,
I am using NRF52832 boars s132 and sdk is 13.1. I have developed my application is read analog accelerometer valie and send to mobile apps. Now i want to also battery...
I'm facing one issue while uploading firmware using BLE DFU.
Details:-
Hardware : NRF52840-DK
SDK : v15.0.0_a53641a
IDE : Segger Embedded Studio v3.40
Mobile App...
We have a Сustom BLE device and observe inconsistent behavior when connecting from this device to to nrf52dk running different SDK versions. - Custom Device connects OK with...
Hi All,
I'm trying to use the nrf52832 as the SPI master to get sensor reading through spi from another sensor. I want to base my firmware on the spi_pca10040 example but...
How can i sample nrf52 own input voltage to do battery measurements?My nrf52 chip is directly connected to a battery and it needs to sample its own input voltage without a...
I have been searching through the info center and can only find the slightest mention of the bsp_board functions.
Could someone help me, locate the right page documenting...
hi sir
i have start my project in NRF52-DK development kit but some BLE card give me data in three channel and i have received all data and give me same like data pls find...
I'm new to use nordic. I am using thingy 52. I would like to add a new custom feature that communicate text via BLE from app, store the text as userid in the thingy and check...
i use 52840, nRF5_SDK_15.0.0_a53641a\examples\peripheral\usbd_msc this example, and change the log level to debug
but i still can not see the DEBUG output information, this...
Hello.
I developing drone by nrf52832.
Developed based on nrf52-quadcopter .
physical web & drone is service uuid as below.
#define BLE_UUID_NUS_TX_CHARACTERISTIC...
Hello, I'd like to connect the nRF52840 to four I2C sensors. These sesnors may or may not have the same address and they will all be at the end of their own 2 meter long cables...
