Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
Objective: create a BLE gateway using the iOS Gateway app and nrf cloud demo
I have failed to make the demo work and am seeking ideas to help me get unstuck
I installed...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
hi,
is there a flag note that DFU Transport done(before the setting file update after DFU Transport done )? nRF52832,S132, SDK 13.0.0，secure bootloader example.
Dears,
I am working with mesh sdk 3.0 and 15.2 with soft device S140 nrf82840, our application using the mesh network topology for minimum amount of time then turn it on...
Hi team,
One of my customer is asking if they can reduce L4 15nH in their nRF52810-CAAA design? If not, what is the function or necessary of the L4, please help to explain...
Hi all,
I'm trying to write code for a BLE Ibeacon that changes its transmit power level after every completed advertising interval. I would like to strobe between three...
Hi.
I have a few questions.
1. Init watchdog timer in Bootloader. After Run application Still running Watchdog Timer?
2. If Watchdog timer still is active. not init...
Hello, I am studying the example ble_app_gls from SDK 15.0.0. with a static password for the board nRF52810, SoftDevice s112. When I write debug messages of the event identifier...
Hi,
I am using nrf52840 dk. Also, I am using nrf_serial library with DMA mode for uart communication. I have a continuous loop running in main and there i read data using...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi.
I am using nrf52832, SDK15.0.0, and S132 SD.
I am using a custom board.
I checked the consumption current of 80uA in system off sleep state.
I want to lower...
First some general info:
* Compiler GCC 7.2.0 GDB 8.0.1
* VisualGDB 5.3R8 Build 1973
* Visual Studio 2017
* SDK 12.0
I try to build an application using the SPI...
