I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello, I have a problem with my nrf52832 customised board
It has loaded the ble_app_uart example of the 15.2_SDK and It have the correct pinout from my board, These are...
1. I try DFU bootloader with OTA, it success.
2. But the Application was gone.
3. If item 2 is real, is that I have to porting the force enter to bootloader mode by botton...
Hi!
I am working on NRF 52840 Controller and Soft Device Version 6.0.0. Coding using Keil IDE in C.
Also developing using Free RTOS.
According to the requirement I need...
Hi,
My development environment is sdk12.3 s132_3.0 pca10040 I want to increase the MTU size to 64 bytes in nus. I programmed as below, but there is no MTU size change. It...
I have been trying to configure a single shot timer as a low power alternative to nrf_delay_ms().
I have my timeout handler configured to do nothing and the timer is created...
Hello all,
I have an ESRPB switch from EnOcean which uses the PTM215B transmitter internally.
I've factory reset the switch to its default state and have confirmed that...
After a few notifications in short succession this code will reliably get stuck in an infinite loop (15.2.0). Can sd_ble_gatts_hvx not be used in this way? Do you have to...
Hi
Struggling getting Directed Advertising to work - I have been through all the examples and have been using the ble_app_hids_keyboard_nfc_pairing example.
My NRF52832...
Good day!
I'm working with electronic part of quest game wherein every player has a "player device" (A) and a various amount of "additional devices" (B).
A is multilink...
I am using ICM20649 evaluation board with nRF52832 interfacing SPI connection. I was able to successfully communicate icm with mcu and get data of accel/gyro on Segger RTT...
We have a discovery issue that seemingly only happens with the Samsung Galaxy S8.
We are using the nRF52832 with SoftDevice S132 v2.0.1, and do directed advertisements...
Hello, I currently use the uart-ble-central example with the 6.1.0 stack. I would like to make two changes. 1.) In the case of received data via Uart, the board jumps directly...
Good day all,
I am trying to build a very simple UART connection between the nrf52840 DK and my computer through a UART dongle.
First, I saw the UART example in the peripherals...
