Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi Nordic,
I have an nrf52832 device where I cannot seem to erase the UICR. I've tried the various erase options from nrfjprog (-e, --eraseuicr, --recover) and those seem...
I am trying to port a program over from Eclipse to Segger Embedded Studio. It is a C++14 project and I am having problems because the STLport library that is included in SES...
Hi:
Recently, I use the SDK --- "nRF51_SDK_8.1.0", the project is \Nordic\nRF51_SDK_8.1.0_b6ed55f\examples\ble_central, I modified the project to notify the data periodically...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
The default SDK v14.2 PCA10040e (nrf52810) ble_ap_templete compiles to 131.7 KB Flash in SES and 34 KB Flash in Keil. I would think would have both project configured similarly...
I have looked over other posts regarding the iRAM and iROM settings for flashing firmware to nrf51822 devices but I am still lost on where to start. I've referenced the page...
I'm trying to create an automated script for deploying the command line tools with the segger Jlink driver.
I'm currently using the 9.6.0 installer with the following command...
So I reinstalled one of my Linux boxes (again) a few days ago, and one of the things I need to do to get all the development environment up and running (again) is get the...
Hi everyone,
I'm currently working on MAX30100 sensor and i need to read this sensor data with i2c, currently i'm able to read mpu6050 and 9255. However i don't have much...
Hi all,
My BLE device uses the NUS profile to send data to a connected smart device. At the same time it should also be possible to connect to a RPi/Linux based gateway...
I now use nrf52832 to do development, nrf52832 and mobile phones to transfer the data is relatively large, I would like to achieve For mobile phones that support BLE4.2, a...
Hi Everyone,
I have been experimenting around with the low power SAADC example in SDK13.
I am using PCA10040 dev board and I have programmed it to start/stop ADC sampling...
Hi,
We've been developing an peripheral HID over BLE using Nordic's SDK, connecting with iOS, Android, and Windows devices. (Board: nRF52832, SDK 14)
We've noticed an...
Using 2.0.0-1.beta on Linux Mint 18.
Have installed pyserial with: sudo pip install pyserial --upgrade --ignore-installed
resulting in:
Installing collected packages...
hi ;
now after i maked a successful connection between smart phone and nrf51822 and i could change the state of gpio pin 20 i find a new problem
i want my pin is still...
