I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
On nRF52 interrupts for GPIOTE, I need to perform one event when a button is pushed, and perform another different event when the button is released.
I've checked these...
When the PPK calibrates and turns off the DUT, does the nRF52832 on the PPK disconnect from the External DUT lines? My DUT has a LOT of capacitance on it, and it takes several...
Hello i use the example ble_app_beacon_s130_pca10028, i'll try to add UART functions, but they not work anybody has this problem, please help me!!
int main(void)
{
uint32_t...
Hi..! Friends..!
I am trying to detect the number of steps on accelerometer.
For which I want to Plot the accelerometer values in real time (with minimum rate 50values/sec...
I would like write music box by buzzer. So I need adjust the PWM frequency continuously.
But i don't find the sample cede which is about adjust PWM frequency in SDK.
Where...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hi all, present I'm working on sdk11.0.0 now I need to move all my projects to sdk12.1.0 . And all my custom projects have dfu support. In sdk11.0.0. when I select board for...
hello ,
i am trying to make communication between two (stm8s+nrf24l01) modules for which i am using this link zewaren.net/.../110 ,
by this code i am able to transmit data...
hello,
i am using ble_uart_app project in that i have added the pwm feature and added my code. i have tested my code seperately it works fine but when i have added in the...
Hello,
I'm realizing dfu.
1st case - for test
NRF_LOG_PRINTF("main start\r\n");
// ******* main loop start ******* //
while (1)
{
enterBootloader();
}...
I'm trying to set a global variable in RAM as uninitialised so it can be read back after a soft reset condition:
uint32_t data __attribute__((section("NoInit"), zero_init...
Developing an application on nRF52 DK board using Eclipse Neon.3 (4.6.3). When the program is run the following message is displayed in red across the bottom:
There are no...
The micro ecc works well in sdk11.0. However, after I recompile micro ecc in sd12.2, micro ecc can't work in S132 3.0.
I append micro Ecc functions to the Uart Demo in...
I am having a strange issue with the serial DFU in SDK 11, s132v2, specifically running either dfu_dual_bank_serial or dfu_single_bank_serial. My goal is to simply get the...
