Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I implemented a custom Bluetooth service on the nrf52_sdk similar the BLE LED project in the mbed site however when I copy the hex file and look at the debug output at the...
I am trying to setup a couple systems to use the Nordic rf sniffer. I have a pca10000, a pca10001 ver 2.0, a pca10001 ver 2.1 and a pca10031.
I loaded all with the rf sniffer...
Hello,
I am sending below setup packet to nRF8001, and i don't get any response form nRF8001. ACI as such works fine, i tried sending diff commands and able to receive...
Hello,
I am using Lenovo (late 2015 release) with android 4.4.4.
Got my nRF51822 Bluetoot Smart Beacon kit and downloaded the applications that are available on Playstore...
I have some very basic code that does not appear to be executing correctly.
There are two versions of code that I would think should have the same result. They do not,...
I am having trouble with setting priority of ADC_IRQn.
void ADC_init(void)
{
nrf_adc_config_t nrf_adc_config;
nrf_adc_config.reference = NRF_ADC_CONFIG_REF_VBG;
nrf_adc_config...
I'm using the nRF52-DK (SDK11.0.0+s132) and added in some example code from the RTC example (the RTC2 tick interrupt with prescaler=0 to toggle a GPIO) to the ble_hrs example...
Hi there!
I don't know much about FCC, UL, CE certification and want to learn. I am using the blend micro module which uses nrf8001 chip in my project. How do I get my...
Hi, i've just started to use the nRF8001, so forgive me if this is an obvious problem.
i'm using the nRF8001 with a microchip PIC processor.
i'm using the ace_tl_demo...
Hi,
I have read ANT Message protocol and Usage and tried to implement shared channel according to section 8.2. I am using nrf51422 and S210 and SDK 10.0.0
My master...
I'm trying to use TDD for my development of a BLE peripheral application, but I'm running into some problems. I'm using Ceedling, CMock, and Unity for my TDD environment,...
I'm trying to scan beacons. This is what I added to the example ble_app_uart_c :
case BLE_GAP_EVT_ADV_REPORT:
{
const ble_gap_evt_adv_report_t * p_adv_report = &p_gap_evt...
Hi all,
I have a problem in architecture of my application based on SD132v3 SDK12. It should interact with an iOS device as a peripheral and receive some data to display...
