Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
HI,
i want to have a application in which a timer timeout say 5 second. and during this timeout there is another timer say 1 second. whenever the 1sec timer timeouts then...
Hi,
The function sd_ble_enable(ble_enable_params_t * p_ble_enable_params, uint32_t * p_app_ram_base) requires now the application RAM base address! Is it 0x20002800?
Hi ~
I use nrf51-micro-esb on GitHub
In Tx-Device: auto sent (data+1) to Rx-Device
But Rx-Device receiver data still the same not Increment....
why in Rx-Device...
Hi everybody
Since quite a long time since my last visit here. Now I come back because a new project using the NRF51822. Because now I'm using the NRF51822-CEAA, I can...
Hello,
I am developing an application where in i want to create a network with One central[not a mobile,pc,tablet etc] and multiple peripherals connected to the central excahnging...
HI,ALL
my Project can not exit the GPIO INTERRUPT HANDLER.
following is my project.
include "nrf_gpio.h"
include "nrf52.h"
include "boards.h"
define BUTTON_1...
I have found the bellowing code which was in s130/ble_gatts_struct_seriallization.c of nRF51_SDK_10.0.0 : ( ble_gatts_attr_md_enc)
/* serializer does not support attributes...
I have two device , one is Tx-Device the other is Rx-Device.
Tx-Device : Auto continued Send 4 bytes data to Rx-Device by Radio.
Rx-Device : Using Radio Interrupt receive...
First of all I'm a BLE novice, so sorry if I'm asking obvious questions. I've built a home project where a battery powered mcu listens for requests over wifi and drives a...
Hello.
I'm trying to do as follows: ONE button used either to wakeup or to put system to sleep. In general almost everything is working but I cannot find how to configure...
HI,ALL
as i known, the BLE key is a six digit pin.
and in the static void device_manager_init(bool erase_bonds) ,the statement shows below:
register_param.sec_param...
According to this post , and this GitHub source file , in the nRF51 chip's mbed implementation:
The ADC reference voltage is 1/3 power supply
read_u16() seems to...
HI,ALL
in the nRF5_SDK_11.0.0-2.alpha_bc3f6a0 , GATT Server Event IDs.
i do not find the read event.
All i found is the BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST .
Now...
Hi, all
Recently I use nrf51822 CEAA, WLCSP package to develop a project on UV (ultraviolet), the UV sensor must be exposed to the sunlight. When we take the product board...
I'm running the DFU example from the nRF5110.0.0 SDK. dfu_dual_bank_ble_s110_pca10028 on the DK and it works perfectly using Master Control Panel, but it does not work from...
