Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hello,
I am working on a wearable device at the moment. To support iOS and Android at the same time, I have implemented ANCS and nRF UART on the circuit.
When working...
I successfully run "ble_app_hrs_c" on BLE_Central example at 38,400bps on the PCA10001 device.
My modification on PCA10001 board as follows;
cut out 32.768KHz X...
I want to store the max possible data on flash using pstorage , but I noticed that I have to increase the number of Maximum number of flash access commands PSTORAGE_CMD_QUEUE_SIZE...
Hello,
I have got a problem with use SPI. I get hard fault after call spi_master_open(), exactly when sd_nvic_ClearPendingIRQ function is call.
This situation is so specific...
link text from this post , i want to make code, when i press button,device goes into sleep mode.so i use this post's code in ble uart app. my code is here.
/* Copyright...
Hello all,
I am new to this domain.
Here is my case:
I am using the Atmel SAMA5D35-EK rev D. board. I was facing JTAG connectivity issues over J-Link.
My purpose is...
Hello!
I have Adafruit evaluation board with NRF8001 module and it works perfect.
I also tried to develop my own board with microcontroller unit and NRF 8001 module...
I have a few nRF51 dongles I wish to use with ANT+ for wireless mesh communication between some robots. I want to connect each to one ATmega 1284p and another Arduino Mega...
I'm using nrf25822, I flashed my firmware using DFU and I discovered the a memory regions starting from 0x0002A000 is written
this memory isn't written when I just use...
link text from this link i want to advertise for 10 second then i want to stop advertise for 20 second then again advertise for 10 second. i want this continuously. for that...
HI
I use 51822 to mesh，reference github.com/.../nRF51 for SDK8.0。
（Routine will chip lock。MDK5.1 Unable to find chips）
But it seems not work，Please give me help。
I'm just getting started with some Nordic development. This is on Linux (Ubuntu 12.04LTS) using nRF51 SDK 10.0 and gcc arm embedded toolchain. I have a PCA10031 and a PCA10000...
When I add a new directory to my project for some source files, I get the following error:
"Browse information of one or more files is not available"
If I move the source...
I am having an issue programming my nRF51 DK through IAR. I am able to compile and build the project, but it gives the following errors when I try to Download and Debug: ...
