Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hello,
i use notifications with sd_ble_gatts_hvx. If I push a lot of data, are notifications overwritten or do they are fifoed ?
How to do a kind of flow control to...
So I'm just getting started with NRF51822 and BLE in general; I have built a simple prototype with the BLE Nano using Arduino+BLEPeripheral library. I have converted that...
Hello,
I've read that some devices (e.g. Nexus 4 and Nexus 7) notify only about the first adv. packets from connectible peripheral and the only solution is to disable continuous...
Hello
I am working on a proprietary radio protocol while dealing with a problem that I stuck at for 2 days now. I am managing to get the radio stuck in a TX state (NRF_RADIO...
Hi,
I would like to ask a question about the power consumption specified in nRF8001 datasheet:
the graph on page 40 shows that the average current consumption is about ...
uart not accepting my static passkey when i added dfu in my project. using ios app nrftoolbox.
programed soft device s110. programed dfu dual bank example project then uploaded...
hi i am trying to setup a connection with CP2130 with nrf51. i am using nrf6310 kit. i flashed the spi slave example into into nrf51. on nrf51 these are the connection pins...
I am attempting to wake up every 250ms using an app timer to manage some background tasks and update our BLE advertising manufacturer data if needed. However, once we enter...
this the origin code of offical,,,this some err?? help !!!!
static int8_t channel_port_alloc(uint32_t pin,nrf_drv_gpiote_evt_handler_t handler, bool channel)
{
int8_t...
Hello,
I am using nrf51822 and I want to get RSSI values as much quick as possible(around 20 samples per second) .
Previousely I used MCP and decreased the scan interval...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi all
We use the nRF51822 with the S130 V1.0.0. Our application initializes the TIMER2 (f = 16MHz) with a EVENTS_COMPARE interrupt on the CC channel 1 to monitor some...
I have an implementation of pstorage that works very effectively in one build of software, but is dramatically slower in another. Specifically it is taking 10 minutes to actually...
Hello everyone,
i just stuck with bluetooth Range in nrf51822. I am transmitting data using bluetooth at +4dBm(which is maximum). In my experiment my nrf51 dongle is moving...
