I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
I'm embarking on a new project involving a sensor network of up to 3000 devices within a warehouse for industrial monitoring, and I'm considering an OpenThread network-based...
Hello,
I'm working on an application where we're implementing the nPM1300 and utilizing the fuel gauge algorithm to estimate battery life. Interestingly, the results that...
Hello,
I am attempting to connect a ST7789 to the nRF9161 and communicate with SPI. However the display is not working and I suspect it is because the gpios output the VDD...
Dear All,
When i connect the nRF5340 Audio DK to the windows PC through the USB, It will be enumerated as a USB audio device.
And then, It will act as the default audio...
Hi, I'm currently using nrf52840 MCU for product development and almost finished my project. What I want is when producing a product, I want to compare the checksum of the...
I am trying ADC readings for connecting my sensors. To better understand and see the values, I have made a simple connection with 4 10k Resistros in series, VCC on top and...
I am working on an nRF52832-based project and I am encountering an issue with achieving low sleep current. Despite setting the TX power to 0 dBm and the advertising interval...
I am thinking of using the sample source code of nRF5340 Audio to realize LE-Audio on a board created by our company.
I have written the source code of nRF5340 Audio to...
Hi, I am pretty new to programming with NRF boards and I've hit a bit of a roadblock.
I started with the BLE Event Trigger example and I have managed to retrieve BLE advertising...
HI Noridc
I am developing with nRF5340, and I need to proceed with DTM test to verify the chip in the production process.
I am currently using this routine C:\ncs\v2.6...
Hi, I'm working on a ble peripheral that uses nRF5340, NCS recently upgraded to v2.6.1, Zephyr v3.4.99. The net core is running the HCI RPMsg controller sample as it is. In...
Greetings all. I am troubleshooting an issue on my BLE sniffer setup. While I don't 'think' this is causing my actual current failure (Wireshark not detecting COM6) I wanted...
hardware:nrf5340dk
case: Bluetooth: Direction finding central/peripheral
I modified the code to change the quantization level of the I and Q data received by the receiver...
hardware:nrf5340dk
case: Bluetooth: Direction finding central/peripheral
I added CONFIG_BT_DF_VS_CONN_IQ_REPORT_16_BITS_IQ_SAMPLES=y in the direction_finding_central...
Hello Team,
Just to give you a background , I am working on a project using the NRF Connect SDK and want to run my application from external flash memory. Specifically,...
