I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello,
I am using the nRF52832 WLCSP with the imprint "N52832 CIAAE0 2207A5", and my FICR reports a codepage size ox 0x400 and a code size of 0x100. This results in a...
Can the nrf7002 be set up to have both a STA virtual interface and an AP virtual interface at the same time?
From all the documentation it doesn't specify that only one...
I am using the Nordic Mesh Library with an ESP32 IDF-based application on the ESP32 side, and I am using ESP32 BLE Mesh. On the Android side, I have created a node to send...
Hi,
We are using the nRF52832 in a battery such that we have a 3V3 LDO configured to turn off under a certain battery voltage. Now during testing we have discovered that...
Hi,
I have made my own custom board with the nrf52811. Therefore I was using the nrf52dk.
I have made connection with my custom board and simply want to blink an led....
Hi,
I am using nRF54L15 DK and nRF21540 EK together. I am using the GPIO FEM mode. Below is my projconfig:
I notice that I cannot use 21540 EK in 54L15, the overlay...
Hi,
I am trying to pull up P0.08 as an enable pin for this switch TPS7A0518
I use the following code and verified on development board
However, when I move to...
Hi, we have a product in production and we are using the HWID which is accessible via this API https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/libraries/others/hw_id...
Hi Nordic teams,
There is have issue when I compile the V2.9.0. For more details
C:\ncs\v2.9.0\nrf\applications\nrf5340_audio>west build -b nrf5340_audio_dk_nrf5340_cpuapp...
Hi,
I m using SDK 2.9.0. After building and flashing my target board based on nRF5340, I get the above kernal panic error.
This is my .config.
and my prj.conf
Are...
Hello Everyone,
I am using nrf52832 and sdk 15.2 for BLE scanning and advertising. scanning and advertising is working parallel. this is controlled by other MCU over serial...
Hello,
I was able many times to download nrf52-ble-image-transfer-demo-master in to nRF52840 DK (PCA100156) and run a mobile application successfully.
Today I downloaded...
Hi ! I'm using nrf52 + SDK 17.1.0.
I found sd_mutex_acquire/ sd_mutex_release, which is great for locking variables that are set/get asynchronously. Next, I'd like to use...
