Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
we're performing an evaluation of using an nRF528xx module with 802.15.4 stack to replace a 3rd-party radio module. There will need to be an AT command protocol for...
Hi i am using nordic nrf52840 chip. and SDK17.1 i am using.
in that under secure bootloader code i am trying to use the nrf_crypto_hash_update() function to calculate...
Hi,
We need to update the firmware of the device through IOS-nRF-Connect-Device-Manager, but the language currently used in our old project is objective-c. IOS-nRF-Connect...
hello ,
We use the nRF9160‘s GPS. We see that the 9160 Thingy use a GPS LNA between the 9160 module and the 9160 GPS antenna?
We want to know, whether we can do...
Hi,
I know that the Bluetooth mesh cannot use long range, but I want to know whether the output power of the node can be controlled to adjust its broadcast range？
Thanks...
hi support team,
for ncs, how to add dir to segger IDE like this one.
for example, like keil IDE separating those two .c into two folder in segger.
Regards,
William...
HI
This is regarding to create a project which supports below peripheral
1. Uart : To interact with Windows application - Working Configured Successfully
2. I2C: for...
The instructions at https://github.com/NordicSemiconductor/pc-ble-driver do not allow building the driver or the examples on a Windows system. Following the instructions takes...
Hi, I developed a BLE and Zigbee custom product, starting from nRF5 SDK for Thread and Zigbee v3.2.0. On BLE side, it connects with Mobile or Tablet using Pairing with bonding...
Hi,
1. Does nRF52840 CKAA WLCSP support QSPI 32MHz?
2. What should qSPI 32MHz measured CLK waveform look like?
3. Is there a 32M QSPI CLK sample diagram actually measured...
I finally had success in getting a SPIM master running with a single SPI slave (Honeywell sensor running CS 4 on the Arduino R3 header) on my nRF9160DK. But now I need to...
Dear all:
I am developing a ble scanner using RADIO Peripheral.
I have 2 questions to ask
1.When is the END event triggered?, How does the hareware know the packet is...
I received the hardfault in the following image.
The function at the address 0x00028C44 is:
The hardfault did not occur again after resetting. I'm not sure why this...
Hello,
We have a PIC32 controlling the NRF24L01 with some sucess so far.
But sometimes we get the chip in a state that we can't get off.
We still cannot pinpoint the...
