hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hi all,
I am working on an application that uses AWS IoT via LTE/NB-IoT. I've got the connection working, and I can publish/read to un-named shadow topic and to custom topics...
Hi Team,
I want to develop an application based on Mesh5.0, but I also want to use functions that in nRF SDK. I find the sd_app_evt_wait() in the main function. But in NRF...
Hi,
I have setup a provisioner using the provisioner example of the mesh sdk.
I have also setup 10 nodes using the on_off example of the mesh sdk.
I have provision...
Hi all,
I have successfully followed this [tutorial]( https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/using-a-custom-secure-partition-manager...
Hi!
I am trying to flash a component on my custom embedded PCB that embarks a NRF52832 through BLE. To do this, I run on my PC a python script that reads from a hex file...
How to enable Read back protection in nrf52832 and in nrf52840 after DFU completed.
i have tried using --rbp all its working but i want to do in code(any register or by...
Hi, I'm using the PCA10056 with NRF52840 and I'm using the P24 Section, there's a pin that doesn't have number and neither is connected to GND...
(the pin in the right down...
Good day!
I've found that with connected proxy and enabled filter node only forwards messages and doesn't use advertising. I didn't found in Mesh Profile v1.0.1 any mention...
I'm using a nRF9160-DK (PCA10090) but I can't see connected device on Programmer (v2.0.0) nor LTE Link Monitor (v2.0.0), both installed and launched through nRF Connect for...
I recently installed the nRF Connect extension for VS Code on my PC(Windows 11, 10700k).
I cannot see my connected boards.
But the "programmer" of the nRF Connect...
I have tried a lot but my DK wont enter in Bootloader mode, or atleast the Bootloader folder does not show up in my Windows 7 machine. I am able to do that comfortably with...
I am trying to program the nRF52840 Dongle with the HEX file according to "Programming the nRF52840 Dongle". The dongle is connected to USB port and the LD2 is pulsing red...
On IN141 Informational Notice v1.1 changes for nRF52840 to revision 3 (build code Fx0) are presented.
One of the changes is "New (optional) filter coefficients for pulse...
Hi all,
I am currently developing audio sampling on a custom board using the nrf52832. I'd like to sample at 20khz and am using the nrfxlib driver for this ( https://github...
