I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
when I call nrf_gzll_add_packet_to_tx_fifo after I recive a nrf_gzll_host_rx_data_ready() I get a Error 33542
how can I see what type of error that is?
I was hoping...
Hi
I have a custom-designed board based on nrf52840 and on that board, I am using NFC pins as GPIO.
On Pin no 0.9 and 0.10, output peripherals are connected.
I have...
I updated my Power Profiler software on the NRF Connect Desktop software.
Immediately after switching to the new GUI, I noticed a significant change in power performance...
I am trying to use the NRFX_WDT design in SDK 16.0.0 on a board using the nRF52832.
In the file nrfx_wdt.c, the allocation index is declared/defined as:
static uint8_t...
The drop down does not list the nrf5340dk.
Using nRF Connect Toolchain Manager I open a command prompt in the v1.5.0 sdk,
cd zephyr\samples\drivers\spi_flash
I did:...
Hello,
I have a project based on Cloud Client v1.4.0 using AWS IoT cloud as the backend. I have made some changes in the code so that I disconnect after sending some values...
The frequency tolerance for ANT stack for an external 32.768 kHz crystal oscillator should be +/- 50 ppm max.
Does it mean over temperature range?
There was the same question...
HI:
Now i am use the OTS to transmit image, if we want to set the MTU=185, how many paramter must config here?
example:
CONFIG_BT_CTLR_TX_BUFFER_SIZE=185 CONFIG_BT_CTLR_DATA_LENGTH_MAX...
Hello, I have created my own C program (in eclipse) that basically should just initialize to an LTE network and connect to it, nothing fancy at this point.
I have come across...
Hi, I tried to set up the environment for the nRF Connect SDK v1.5.0 using nRF Connect for Desktop on Ubuntu 18.04.
In step 2 (Cloning the SDK), I got some errors while...
I use arduino to program a nRF52832 board. I had problems to move a running project with a ST7789 SPI display to the nRF52832. I use the Adafruit lib to drive the display...
Hi,
My custom card has ic nrf52832QFAAE0 AND NRF52DK has ic NRF52832QFAAE1.MESH SDK EXAMPLES runs properly on NRF52DK but not working on my hardware with ic NRF52832QFAAE0...
Hi,
What cellular connectivity, the provider's DNS, and backend cloud services, invariably connecting over MQTT is transient and the internal blocking timeout of mqtt_client_tls_connect...
