Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi,
In the attached study from Nordic and Energizer there is data regarding the discharge behavior of a CR2032 Coincell battery under different conditions. I wanted to...
We are using nRF9160 as the host MCU and Modem for communicating to server. If VDD_GPIO is powered by 3V external supply and SIM card is powered by VDD_SIM i.e. 1.8V Do we...
Hi,
I have a hex file generated by uVision Keil 5 IDE . I would like to combine this with the hex file form the soft device. These two hex files once combined would help...
Hi,
I would like to change the manufacturing data with time. My advertising_init function implements the following line
init.advdata.p_manuf_specific_data = &manuf_data_response;...
I've been using the nRF52840 DK to load the firmware into my custom nRF52840 board using nRF Connect v2.6.0 and programmer v1.0.2.
However, on another laptop when I install...
Hi,
We have developed a custom board using nrf52832 chip and currently everything like (BLE, TWI, ADC etc) is working fine but we are having issues with the UART. we have...
Hi,
We are using nRF52840 with nRF5 SDK ver 16.0.0 with Softdevice S113 ver 7.0.1.
We use the radio timeslot to implement low level radio comm with very tight timing requirements...
hi i am using this to capture the adc value data_ADC=adc_buffer[1]*(1024+gain_error) / 1024 + offset_error - 0.5; data_ADC_double=data_ADC*3.6/1024; MULTIMETER MEASUREMENT...
When I used nrF52832 mouse application, the SDK version was 15.3. When I connected to MacOS, I had to make several attempts to connect. Can you tell me why?
Thank you very...
Our nRF52832-based board is powered by a coin cell battery, and spikes in current can cause the voltage to drop. This is okay early in the battery's discharge curve, but as...
The communication between the UART peripheral and the nrf52840 works fine until some device connects to the nrf device via BLE. Using a digital logic analyzer I'm able to...
hello
now we want to use nrf52840 qspi interface to connect with fpga. we have a question:whether nrf52840 could be used as qspi slave, and fpga used as master?
if it...
Hello everyone,
I am a beginner with BLE and the nRF52, so I apologize in advance if this question is pretty simplistic. Basically, I am trying to achieve the most data...
