I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
Hello, The nRF9151 hardware design guidelines (power sequence) require VDD_GPIO to be applied at least 6 ms after VDD and ENABLE, after the hardware boot. In our design a...
Hello,
As per data sheet "Endurance 10 000 write/erase cycles"
Does it mean do we need to consider either write or erase as 1 unit or both write and erase as write will...
Hello,
We are developing a product based on the nRF52840. According to the blog post nRF Connect SDK gets Long-term support with version 3.4.0 , NCS v3.4.0 declares the...
Dear Nordic Semiconductor Support Team,
We are preparing a small, non-commercial research experiment to investigate the timing characteristics of Bluetooth Low Energy (BLE...
I tried to switch to OAT. Now I use new API
" api.nrfcloud.com/.../ long-range/devices/bulk" with OAT bearer token for devices creation
instead of old API: " ">api.nrfcloud...
For nrf Connect SDK, can I config CONFIG_BT_ID_MAX = 2, both adress type are Public for below use case?
ID with index = 0 for peripheral role and for connect and bonded...
We're running a small voice-activity model on the Axon NPU (nRF54LM20B, NCS 3.4.0, Edge AI Add-on v2.3.0, Axon compiler 1.5.0) for a body-worn voice device. Features come...
While we understand that the RRAMC controller on the nRF54L15 performs writes to RRAM using full wordlines, the datasheet indicates that the nRF54L15 RRAMC supports writes...
Summary
On a small fleet of identical nRF52832 units running the same firmware (NCS 2.5.1, SoftDevice Controller, BLE peripheral, LFCLK = RC with calibration), individual...
Hello Nordic support,
We are designing a battery-powered device using the u-blox NORA-B206-00B module, based on the nRF54L15. u-blox support recommended contacting you regarding...
Hello,
I have a nRF93M1-DK and I need to connect the nRF93M1 UART directly to an external MCU.
I can use USB1 connector just for power up the module but I need to totally...
We are migrating following your November 11 notice. Two read-only Identity Service operations remain unresolved:
- POST api.identity.nrfcloud.com/.../verify-jwt authenticates...
Hi,
just got my PPK2 and noticed some strange behavior:
the only thing connected is USB data/power, no DUT. Power output is off. If you start logging it displays some...
Hi
AFAIK CRA needs SPDX 3.0 which can no be generated by west ncs-sbom in NCS 3.4. Will SPDX 3.0 generation be backported from 3.4.99/3.5 to 3.4 LTS?
Thanks in advanc...