Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
I can't seem to find the right configuration item to set to disable the spinning up of the sensor_sim task, which I have no need of in my application.
I've tried setting...
Quick question I think. I'm using the NRF52 to program a PIC16 over SPI. The PIC16 switches it's line to output once it receives a particular command so as such I need to...
Hi,
I'm trying to mimic a fully functional zigbee color light bulb using the nRF52840 dongle.
Starting with the NRF5 Zigbee example light_bulb (examples/zigbee/light_control...
I apologize if this question is stupid
I want to read data in p_adv_report. I use the command NRF_LOG_INFO ("name =% x ", * p_adv_report-> data.p_data); but it's meaningless...
I am trying to use I2C (TWI) to communicate between my custom nRF52811 board with an Arduino. Currently my program hangs at the while (m_xfer_done == false); loop as m_xfer_done...
Hi Team,
We wanted to verify Sleep current numbers for nRF52833 SoC based custom development kit.
Is there any readily available firmware to verify these numbers?
...
I'm teaching a course, using the nRF52840-DK board as the lab platform.
Students download Segger Embedded Studio and compile the "Hello World" project from the 'nRF Samples...
Hi,
I have built a prototype that has two SPI slave devices connected to it and it works perfectly. I have now tried to add an SPI SD card aswell by following the FatFS...
Hi,
I'm now using nRF52833 DK to do the AoA test. I achieved the IQ sampling for a single antenna, but when I tried to switch between multiple antennas, the IQ results seems...
Hello!
My problem is that I am getting duplicates of the ACK packets I send from my PRX device to my PTX device.
To debug this problem, I configured my PTX to continuously...
Hi Devzone:
Is there a way to designate one ram block exclusively for radio use? The reason I'd like to know is the following:
Under nRF52833 AHB multilayer section, there...
I need a specific extended panid. Refer to the CLI example and add the following program:
Through the log, the extended panid returned by the device is 0000000000000000...
Hi,
I am developing an application with to 7 transmitters (peripheral) and one receiver (central = nrf52DK), all NRF52832.
I have 1 question and one problem to solved...
