hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hi, As the title states when I try to add characteristic to my custom service the function returns error 16. I have set NRF_SDH_BLE_VS_UUID_COUNT and adjusted the linker accordingly...
Good day,
I am starting a new project where I am using the ANNA-B112 BLE device from ublox in a custom design. The ANNA-B112 interfaces with a host MCU over UART. I would...
Hi,
I have added nus service to the relay central and peripheral example.The relay board advertises and i can connect to the peripheral part of device through the nrf connect...
The mesh health model state is not restored following a reboot in the current version of the Mesh SDK using the light switch example.
According to the documentation, the...
Hello folks, I am new to Thingy 52 PCA 20020 model and I have downloaded nRF SDK 15.2 and I am using a Segger J-Link programmer/debugger. The thing is I would like to get...
In acces.h there is the publish period format definition, which is
/** * Model publish period structure. */ typedef struct { /** Step resolution. */ uint8_t step_res : ACCESS_PUBLISH_STEP_RES_BITS;...
Hello,
I was surprised that gcc did not optimized my strlen("FOO") construct (worse, in a code review, I argued that the compiler would do the optimization…)
It seems...
Hey there,
I am trying to develop with the Bluetooth Mesh SDK for NRF5.
We have two chips, NRF52840 and NRF52840/NRF52832and are using the light_switch example from the...
I need to save energy for my ble application. So I turned off the sensor when there was no ble connection. A ble connection is a condition for me to turn on the sensor, but...
How exactly are the UART pins selected for the nRF9160? I've searched and am unable to find a file to configure pins. I need to change to pins from the development board to...
Hi,
I'm working with the SAADC on an NRF52832. I'm using the SAADC driver from SDK15.2.
I have a problem with the calibration routine because it's generating DONE events...
Hello,
I am developing an application on the 52840 and so far find the SDK documentation quite confusing and somewhat contradictory. I need to write a simple TWI (I2c) master...
Hi, I’m located in Liège, BELGIUM.
Using the nRF9160DK, an orange SIM card, MODEM firmware mfw_nrf9160_0.7.0-15.alpha I managed to make run some sample code:
mqtt_simple...
