I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Im trying to detect power off. The signal power off looks like:
The time to get 0V equal 15seconds. GPIO EVENT and COMP do not see changes in the voltage level, they are...
Hi folks!
I'm working with a couple of nrf52832 on custom boards. I'm trying to implement a procedure for firmware updates. I've already played with the examples from the...
I have found many questions regarding passing bonding information from the application to the bootloader (e.g. https://devzone.nordicsemi.com/f/nordic-q-a/34497/dfu-with-bonds...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
I am using "twi_scanner" example code on Development kit. I connected HDC2010...
Errata for nRF52832 Rev 2 version 1.2, errata item 20, RTC: Register values are invalid, has a recommended workaround that i'd like to ensure i've implemented correctly -...
Hello,
I have a project that does what the title states, create a Mesh Network using the Nordic USB Dongles then provision a smartphone using GATT to access the Mesh network...
Hi All,
I have used eeprom(AT24c512) and spi(Winbond 25q16) in my Product.Usually all work working fine But sometimes my memory Behaves like volatile ;sometimes My Memory...
Building ‘secure_dfu_secure_dfu_ble_s132_pca10040_debug’ from solution ‘secure_dfu_secure_dfu_ble_s132_pca10040_debug’ in configuration ‘nrf52832_xxaa_s132’
Linking secure_dfu_secure_dfu_ble_s132_pca10040_debug...
Hello,
I'm trying to update the SoftDeivce used on our product from s140 v6.0.0 to 6.1.1, but am running into issues. Per the release notes it sounds like no updates / recompilation...
we use 52810 connect with iphone6, then read the RSSI value, it will disconnect with the iphone6.
reconnect the iphone6 and read the RSSI value, it disconnect again.
we...
After doing some reading, I realized that the light CTL server model does not contain the generic OnPowerUp set message. It is contained within the light CTL setup server...
After import a project in to SEGGER and included paths of header files
While compiling i got the error like below
sorry, unimplemented: non-trivial designated initializers...
Hi, I am using a system where I am using nrf52832 nordic chip. I generate a custom ble service using this ' https://github.com/bjornspockeli/custom_ble_service_example ' github...
Hello.
I would like to use the SPIS module on the nRF52840 DK. I configured it by following the examples given by Nordic.
When I use pins P0.14 (nCS), P0.15 (SCK), P0...
