I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
nRF52840
SDK15.3
My question is regarding the low frequency clock.I am initializing the low frequency clock as follows:
When TASKS_LFCLKSTART is initiated in line...
Hi Nordic,
I have been trying to communicate with KX 124-1051 using IIC in nRF52832 . I am getting NACK from slave every time i send the device address. I checked all the...
Hy to everyone
I'm working with SDK15.3 Ble_Blinky example for my nRF52840 Dongle (pca10059).
First to know, I'm wokring with c++ and the whole Project is compiling without...
I'm using this module to develop a toy that needs a couple of sound effects. I just don't want generated tones but previously recorded audio files no longer than one second...
I wanted to try the bootloader related example. I was using the IAR to run peripheral examples.
But for bootloader example, I saw that IAR was not listed. So installed the...
I read the following QA - https://devzone.nordicsemi.com/f/nordic-q-a/41237/on-dfu-jump-address but still have doubts
1. Is it safe to set the Bootloader RAM start address...
Hi,
Hardware：nRF52840 module, Power Profile Kit. SDK：nRF5_SDK_15.2.0_9412b96.
Using Power Profile Kit to measure the low power consumption current of an nRF52840 product...
Hi,
I am currently trying to use SDK 15.3 secure serial UART bootloader (from the example in nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040_uart) on a custom...
hi, I am working on the bootloader with s132.5.0.0 on sdk14.2.0. I am trying to using the uart to flash the chip.
I build the bootload example bootloader_secure_serial,...
I'm using three PCA10056 boards to test mesh example(Meshv3.1\light_switch).
[light_switch_client] ---> [light_switch_server1] ---> [light_switch_server2]
*Put the server2...
I am testing a mesh network, using the NRF52832 modules, SDK 15.2 and MESH_SDK 3.0, provisioning the nodes with nRF Mesh android app and using a modified firmware for the...
I am trying to build UART support into my current project but the compilation of the nrfx uart driver fails. See error below:
Any idea how to solve this? Is there good guide...
Hi,
I'm using the NRF52840 with the "nRF5_SDK_for_Thread_and_Zigbee_2.0.0".
I tested the zigbee light_bulb example and zigbee light_bulb + ble. It works fine so my next...
I'm trying to extend the light_switch client example (from mesh SDK 3.1.0) to a gateway. The gateway will consists of nRF52832 and a WiFi module connected via serial interface...
As the title descripes i get an error with a file name in it but i can not locate this file.
I am working with the 802.15.4 wireless uart example on a nRF52840 DK. I only...
