hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Greetings,
I'm getting some trouble trying to fix a warning. I'm running the exemple ble_app_uart_c from the folder ble_central. When I run it, I keep getting the warning...
Hi,
From the pwm driver, there is a function that use sequence that control the dimming while not blocking other task in the program, may i ask if there are any function...
Hi,
is it possible to use the GPIOTE in OpenDrain mode?
I want to use the Timer with an GPIO. So i use GPIOTE with PPI connected to the Timer. This works. But my Pin Configuration...
Dear Nordic Team,
I am trying to use the MWU to safeguard RAM of my application. Since softdevice also use this unit, I wanted to understand that where I can write the...
Hi!
I can able to read values from BMP180 but I am getting random values.It shows temperature values in some 200 range like that.How to get proper temperature value??? ...
board: custom board nrf52840
IDE: keil5
SoftDevices: s140 V6.0.0
SDK: 15.0.0
hi, I want to decrease my consumption of my board.
Now, i enable the SoftDevices and...
When I am using peripheral/cli example and debugging through RRT, I see following outcome when I am typing commands.
OUTPUT :
Command Line Interface example started...
Hi,
I am working on light switch example. I am broadcasting a message from client to servers using the API access_model_publish() with the opcode SIMPLE_ON_OFF_OPCODE_SET_UNRELIABLE...
Hi:
When I tested the DFU function of BLE, the upgrade was unsuccessful, and the APP print log prompt appeared to be a CRC check error.
The SDK version I am using is nRF5_SDK_15...
I reference demo1 of PWM driver example in SDK15.2.0, I make myself PWM driver. the official demo1 use pin17-20 as PWM channal1-channel4, but I use Pin9-P12, I modify the...
Hello,
I would like to measure the frequency of a signal and I use PPI, a timer and input capture to achieve this. Here's the configuration :
The frequency of my signal...
Good evening,
I am using NRF52840 board with softdevice S140 and SDK version NRF5_15.2. I am currently trying to compile the ble_app_hrs_rscs_relay example on SEGGER studio...
Hi ! I have attached the PCB design and schematic provided by Nordic for nrf52832 which is said that its also same for nrf52810.
I wanted to use the nrf52810 board for beacon...
