I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
Hi,
I have a smartwatch that has a nrf52832 chip inside. It firmware runs on S132 SoftDevice ver 2.0.1 and has an OTA bootloader which supposingly allows me to upload firmware...
I am evaluating the nRF5284 SDK 15 Module in HCI mode. I am trying to scan Extended advertise when: 1.Extended non connectable non scannable advertising, Primary_Advertising_PHY...
Hi,
I have just purchased a nRF52840 usb dongle ( https://www.mouser.in/ProductDetail/Nordic-Semiconductor/nRF52840-Dongle?qs=gTYE2QTfZfTbdrOaMHWEZg==) .
I would like...
Hello, I am a beginner and I just got a Raytac "MDBT50Q" bluetooth 5 module based of nRF52840 Soc.MDBT50Q does not come with a builtin frimware to respond to AT-commands.Can...
Hello, i have this problem with DFU, in Mesh SDK v3.0, i am using PCA10040.
this is my boodloader_config_default.json
and i am using this for make the pkg.
and...
Hi!
For our development purposes I am implementing NRFUTIL 0.3 for mesh on Android/Java, migrating it from Python code, via UART/Serial, for DFU purposes
It looks like...
Hello,
I am having difficulty using a single TWI to support a DAC (MCP4725) and IMU (BNO055).
I am using nRF52 DK, and SDK 14.3 with the SEGGER IDE. The DAC is running...
Hi,
I am trying to run lte_ble_gateway sample on nrf9160 DK, but in debug I can not catch breakpoint on main().
When I going in debug mode step by step I find that the...
Hi
I am new to the NRF52840. I am trying to receive data from nrf24L01+ to the nrf52840 Development kit. I find some examples from the SDK radio receiver using PCAl0056...
Hello all：
I am using nRF52-DK（pca10040）to do some tests.
I want to use gazell and at the same time, I want to detect the events of the NRF_RADIO, connect it to PPI. ...
Hello,
I am using Eclipse to create a project using code from ble_app_hrs and I am developing for a nrf52832 chip. Unfortunately, I am getting a "was not declared in this...
I send a sequence of characteristic writes to my device, in code based on the nRF Toolbox. Sometimes I see this error message. Why does it happen and what steps can I take...
Hi Team
I created an own interface layer using the mesh SDK's "flash_manager" to have a simple API for accessing my application flash area.
Now, I am facing the problem...
Hi there,
I am migrating a project from SDK13 to SDK15.2, where I need to change the advertising data dynamically and change the ble_gap_adv_params_t properties type between...
I am using SDK12 with nrf52832. UART working fine (with FIFO) and Timer1 also works.
I wanted to set a 1 minute timeout around the UART dialog to handle disconnection etc...
