Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Hi all. I try to configure QSPI example to work with w25q64fv flash. I connected all pins from flash to same pins on nRF as on PCA10056 DK board. After all i have "Data inconsistent...
Looking at the code in SDK 15.0.0 I think app timer library will be reinitialized. Is there a way by which I can check it the library is already initialized and initialize...
Just installed Mac v. 2.4.0 of nRF Connect, and the "Start Scan" button is disabled. Here's the log:
2018-07-05T13:43:15.834Z INFO Application data folder: /Users/rob/Library...
Hello,
I am developing on the nRF51 and soft device version 8.0.0.
I have created a new service that has a 128-bit UUID that is based on the base UUID: 00000000-0000...
Nrf51822
SDK : nrf51_12.2.0
soft device : s130
Example : ble_app_beacon
I’d tried single channel adverting with nrf51 beacon. And I referenced this way to disable...
We are using the nrf51822 chip, however after typing the command: nrfjprog --memrd 0x10001080 -f NRF51, the chip is no longer able to start.
We have tried resetting the...
Hi Everyone,
I have successfully configured RTOS and BLE alog with onboard LEDs blinking into an RTOS code.
Everyhting runs fine if i run only the 4 tasks of LED blinking...
Hello!
I need to send 20 x 20 bytes with the nRF8001 and would like to reduce the transmitting time as much as possible to set the MCU and nRF8001 in sleep mode as long...
Hi,
I am confused about the ROM layout, would you please correct me? Thanks.
Based on my understanding, for open bootloader scenario(like nrf52840 dongle), the bootloader...
I am using the nRF52832 with the S132 soft device. I am trying to send a large amount of data (~5 kB) from a phone to my BLE peripheral. I am wondering if the queued write...
I Have attached my project which is an SDK 15. project, starting with the simple twi sensor project and including some functions calls from gpio from SDK 14.0, porting gpio...
Hi,
The following is the guide under this ticket: devzone.nordicsemi.com/.../where-i-can-find-the-example-of-usbd-dfu-for-pc-side
Terje said "you can use nrfjprog with...
Hello everyone
The following warnings and errors occurred
Warning[Pe223]: function "sd_flash_write" declared implicitly D:\ZIP\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a...
Hi I am developing on Adafruit LE UART Friend ( https://www.adafruit.com/product/2479 ) platform. Compiler: GCC 7.2.1 IDE: NetBeans NRF SDK: 12.3, SoftDevice S130 Debugger...
Hi,
I am trying to interface ESP8266 WiFi Module: https://www.amazon.in/OLatus-ESP8266-Wireless-Transceiver-Raspberry/dp/B072BG8LW1/ref=sr_1_1_sspa?ie=UTF8&qid=1531738374&sr...
