Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hello,
I am trying the example code, heart rate BLE peripheral application, on the nRF52 DK. However, I cannot see the screen fill with data in the heart rate monitor,...
hello,
i am working with a long range ble long range transmitter and receiver which will communicate over long range to send a ble nus string in nrf52840, so i set tx power...
I am working with SPI and SPIS examples ( sdk version 13). SPI of nrf52 is full duplex. In the example, I can send data from Master board to Slave board then Master board...
Hello!
I use 2 board nrf52840! I want to transfer large data ( 1~2MBytes) from board1 to board2 with wire to connect. Can have solution for me? (SPI I2C or uart).
According to the description of S132_SDS_v5.0 on page 82, when the establishment of connection, in accordance with the BLE protocol, softdevice will be interrupted frequent...
I am using nRF52840 and the power profiler. I am trying to measure the current to evaluate the scheduling of BLE. Now I am using the ble_uart_c example and I changed the scan_interval...
I'm trying to set up SPI example from SDK12.3, but I get error at line 53 of main.c
static const nrf_drv_spi_t spi = NRF_DRV_SPI_INSTANCE(SPI_INSTANCE);
It's saying...
Dear friends,
i am using Power Profiler Kit with a nRF52832 DK(PCA10036). However, i just find three versions of SDK on www.nordicsemi.com/.../nRF52-DK . My problem is that...
Hi nordic,
nRF5_SDK_14.0.0_3bcc1f7\Raga\examples\ble_peripheral\ble_app_ancs_c FDS\pca10040\s132\arm5_no_packs
I had a problem when I was using FDS,When I use the GC...
Dear friends,
I want to use Power Profiler Kit to monitor the current waves of nRF5x DK, and i followed the following configurations:
The PPK board (PCA63511) is connected...
How do you do
Now use E: \ Nordic \ nRF5_SDK_12 2.0 \ examples \ peripheral \ pwm_driver \ pca10040 demo5 pwm_driver routine
There are two problems:
How to change...
I run into this topic during seeking an answer to my problem and for me, as well as for the author of that question the answer doesn't work properly. But wouldn't it be easier...