Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
By design, the TI LP55231 LED driver IC will fail the TWI write of the reset register (0x3D). It's necessary to reset the IC in an edge use case. I'm using the nRF51822 HW...
Hi,
I want to write a characteristic, the value size is fixed, for example the size is 4 bytes. When I try to wirte 6 bytes from the client, the first 4 bytes is writed succesfully...
Hi all,
I have the nRF52 DK programming consistently without any trouble both on Kiel and using the nRFgo Studio.
My problems arise when I connect a 3rd party module...
Hi,
im trying to set up 3 PWMs for simulating a RGB LED with the 3 leds on the nrf52-dk.
I need the following behavior:
pushing on a button increases the width of the...
Hi,
I have implemented a custom application(Lets name that file app.hex) which works and sends the data to phone via BLE on my nrf51822 DK. I am using the s110 v8 softdevice...
Due to some constraints in the manufacturing process of my product, there is substantial mechanical variation in the BLE antenna. I can constrain this variation to a degree...
Hi,
I am trying to program MDBT40 with Jlink and having some problems.
Here is the scenario:
I have two versions of the MDBT40. One that I took off a BLE NANO (RedBear...
Hi,
I tried to get the sample ble_app_uart to work on NRF51422_DK with the S130.2.0.0 soft_device.
The compilation and programmation of the board is OK.
The soft run...
Hi all, i recently posted some topics about my application to receive support, everything went good but now i need to add a last step to the project, and i would like to have...
I am using nordic_sdk_10 for PCA10001. what are the BSP changes and config changes needed after replicating PCA10028 for DFU over UART.
I just changed CFLAFS & ASM FLAGS...
Hi,
I am storing data using pstorage module but when i power off my nrf51-dk board, the contents get deleted and not retained in memory. What could be the reason for that...
Hi,
For a new design with nRF51822-QFA, planning to use Johanson Balun and Chip antenna as shown in attached diagram. Not using any tuning components between Balun and...
Hi,
I was wondering why DFU_IMAGE_MAX_SIZE_BANKED is calculated as
(((DFU_REGION_TOTAL_SIZE/2) - DFU_APP_DATA_RESERVED))
and not
((DFU_REGION_TOTAL_SIZE - DFU_APP_DATA_RESERVED...
