Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hello,
We're interested in measuring the precision of our external crystal, but don't have the equipment to measure off the crystal directly without affecting capacitive...
Hi,
I am trying to run nRFToolbox App, I imported the project to Android Studio but I get the following error when I attempt to run it:
Error:Execution failed for task...
I just switched over from SDK v6 to SDK v7.1 (installed via those Keil Packs). The UART has suddenly stopped working (via Segger USB COM port) and I can no longer see any...
Hi Nordic,
I used PIC32 for SPI Master and nRF51822 SPIS slave. I used shortcut for my spis in nRF51822 and I need to know the right time of acquiring the semaphore and...
I have a 32 byte string to read and write using SD110. In the MCP I can read (using read long) the whole string without any problems. When I try to use write long, MCP times...
I'm getting started with the ble_app_hrs_s110_pca10028 (nRF51 PCA10028) example in the nRF51_SDK_7.1.0_372d17a_packs.zip SDK. See the tags for my hardware setup. I'm using...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Hello ,I want to scan the Bluetooth peripherals through one master application and want to display the Bluetooth peripheral names on serial window like what master control...
I am new to nrf51822.
I am trying to convert my Arduino code into NRF51822
I need something like this
currentMillis = micros(); //microseconds since the Arduino board...
Hi,
Without dissecting the provided Raspberry Pi Debian packages -- is there a list of the required Linux kernel modules and binaries required for the IoT Dev Kit example...
Hi there. I'm currently trying to run the BLE_APP_HRS example from IAR workbench on nRF51822-Evaluation-Kit.
We are very interested in using this chip in our upcomming products...
Hi All,
I noticed CSR has just released something called CSR mesh, please see: http://www.csr.com/news/pr/2014/csr-mesh , and a demo video: http://www.youtube.com/watch...
I'm renewing my search for a point-to-multipoint radio system, preferably based on the nRF51822. Basically, I need to be able to connect up to 32 (or more!) nodes to a master...
I am trying to implement a mesh protocol using the nRF24L01+ transceiver.
After reading the product specification, I have concluded that the Enhanced ShockBurst cannot...
