hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Hi,
I want the NRF51 to respond to a received packet from a particular device using register TIFS to control the interfame timing.
For TIFS to work I have to set the...
Dear Nordic,
is it possible to build a simple data bridge at speed of 115200 and up based on nRF51822 with CTS/RTS support and a fixed pin code for nRF51822 pairing?
I am working on a multi-node network application with multiple transmitters and receivers and I have a question about timing for chips like the nRF24L01+. I would like to...
Hi
In my case i have gpio interrupt for every 25ms. so i change button detection delay t0 10ms.
and i given timeout in all while loops of twi_hw_master.c.
but my...
Hi,
we have nrf51822 custom hardware.
we are flashing application through j-link.
but after every flashing , i need to do switch off and on the device.
then only...
I have no power on my nrf6350 display
I programed the board with the display jostick example but cant see nothing on my lcd of the nrf6350
any advice?
thanks
...
Hi:
I'm fresh in use BLE.
when i installed SDK, i could not install the lastest version v4_4_1,but can install v3_0_0.
My system is MS win XP Pro SP3.
Please tell me what...
hi,
i took the same example of BLE_LBS, as it is working properly in case of writing to the device, but when i implemented my own for writing to the server, it is not working...
Hi,
I need to send more than 500 packets(each 20 bytes) to the master for every 1 minute, through the timeout handler. But i cannot able send all the packets, btle_connection_timeout...
Hi,
i have some trouble with the method __WFI ();
I have the following code:
while(device_status == false) // Gerät ist im Schlafmodus
{
checkPowerConnector ( );
__WFI...
1.Can we use the Timer0/Timer1/Timer2 for doing something?
2.What source of IC the SD have used?
3.What source of IC we can use for our application?
4.I used the compare...
Hi - I am completely lost and I'm really hoping someone can point me in the right direction. I'm simply trying to get started with the nRF51922 development kit and nRFgo Motherboard...
I opened both the NordicSemiDemo.xcodeproj and nRFDemo.xcodeproj in Xcode 5.0.2. When I try to run them (Product->Run), I get the splash screen in the simulator, but when...
