I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
Hello,
I am using nrf52832 as a peripheral and running SD S132. l am looking for an ble peripheral example wherein the Out of Band security level is used.
Can you point...
Using Programmer v4.0.1 can successfully read the NRF51822AB, but upgrading to the latest version 4.4.2 results in a failure to read the device.
Additionally, after...
We are working with nRF52840 and NCS2.6.1. And we want to change pin configuration for UART1 instance during the runtime and we have also used following ASYNC UART configuration...
Hello,
I am trying to upload certificates to my nrf9160 chip on a custom board. I have done the following: 1. Loaded AT_CLIENT from the samples
2. Tested all AT commands...
Hi
we are using the BT HCI to add BT functionality to nrf9160 using the thingy91 hardware. upon updating the sdk from 2.7.0 to 2.8.0, we are getting the error bt_hci_core...
I want to read and write data such as incline and resistance from the Zwift app using my nrf52dk device. Based on the information I found online, it seems I need to communicate...
Hi,
My custom NRF52840 device has two interfaces (UART and USB) for host connection. I have successfully verified firmware upgrades using mcumgr from a mcuboot via the UART...
Hi
Use the following routine NRF\nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs.
Use IOS APP Enable the data to be sent once...
When evaluating BLE mesh with multiple nodes the nRF52840 Dongle is perfect to keep cost and physical size down.
I thus have one nrf52840 DK and a couple of nRF52840 Dongles...
We can get the active end points and list of cluster in end points.
But is there a way to get list of attribute and types of attribute in each cluster?
Hi community,
I read these articles about match network for antenna:
General PCB design guidelines for nRF53 series - nRF5x - Hardware design, test and measuring - Nordic...
Hi,
Like some other users, I face an issue migrating from ncs<2.6.0 to ncs 2.7.0 regarding radio notification.
I saw it is possible to use the PPI for the EGU IRQ to be...
Hello, I am using the Soft Device S140 7.3.0 with nRF5 SDK 17.1.0 and the nRF52820 as a peripheral in an NUS application. Initially, the transfer was slow but worked perfectly...
Using the nRF54L15 Development Board.
Did try to run the "nRF connect for desktop" - "Quick start"
I do not get a reply from the Board when doing one of the samples. ...
