I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hello,
when I play around with the matter template example, I always get a thread child device. How to get a full thread device with routing etc?
Thanks, Edi
Hi,
I'm using a Azure IoT Hub to connect some devices to the cloud and then uses the Direct Method to send messages to the devices. I can send messages and receive the response...
Hello,
I want to work on NRF52832 using VL53L3CX. When I look at the SDK, there are source files for VL53L0X and VL53L1X. I have previously worked on VL53L0X using this...
Do the LED drivers on nPM1300 have any ability to control either current or do PWM dimming? led_set_brightness() seems to not do anything and from the datasheet its not quite...
We have an nRF52833-based board, software is based on Zephyr and Nordic SDK 2.1.2. One of the SPI interfaces connected to external flash (Winbond W25Q80DVSNIG) Board is battery...
I have successfully implemented an interrupt-driven method to read data from the MPU6050 sensor on the NRF52840, and it functions as expected. However, I encounter an issue...
Hi Nordic team,
The LTE link monitor app is not showing up in my NRF connect for desktop v3.6.
What would I need to do in order to add it?
Is there a http link you...
I have written the code to test the RSSI signal, and the segger shows the result on the debug terminal, However, the debug terminal can only show first 500 data, the first...
Hi,
I have installed NCS 2.7.0 using the nrf command line tools, and followed the tutorial to install the NCS VSCode extension in VsCode. However, when I compile the Matter...
After I flash my code,I get imformations as follow:
*** Booting nRF Connect SDK v3.5.99-ncs1 *** ***引导nRF Connect SDK v3.5.99-ncs1 *** ***引导nRF Connect SDK v3.5.99-ncs1...
Dear Sirs!
I used SDK 12.2. Product was developed some years ago and now I am working for upgrade. One of new features is UART. I faced very strange problem.
I send...
Hello,
I am developing a HID device with DFU OTA and would like my customers to be able to upgrade this product independently via DFU OTA in the future. I would like to...
Hello Everyone,
I would like to interface the Accelerometer to nrf52810 via TWI pin P0.06 as SCL and pin P0.09 as SDA. I have to read the accelerometer data and send over...
Hi Nordic I am transmitting the dmic stream from nRF5340 dk to nRF5340 Audio dk. But I am not hearing the nRF5340 Audio Dk. Getting below Wrn's How can I hear the audio on...
